Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Monrovia

  1. Monrovia

    EXL lenth problem

    Thanks parnum for the trick. I changed the adc dig 1 = 0 (immediate seizure) and made change in the nadap list. Since there is PRE which is dialing 161 in the starting of the number, i added that into the nanls. <roddp:dest=2&3; EXTERNAL DESTINATION ROUTE DATA DEST DRN ROU CHO CUST ADC...
  2. Monrovia

    EXL lenth problem

    Hi guys, I am facing a problem with the number length setting. I have set the length MIN=4 & MAX=4. But when the extensions dial the remote exchange extension numbers it starts dialing & sending signal immediately in 2 digits. <RODDP:DEST=2&3; EXTERNAL DESTINATION ROUTE DATA DEST DRN ROU CHO...
  3. Monrovia

    {BP250}Direct Transfer a specific external number(Incoming call) to specific agent or extention

    Dear XS As far as I understood, he want to land particular calls to specific extension 200, where there is 11 extension attached to that group. I believe, you have to cut down the last 3 number of the exchange number not the first 4 digits, and put 200 there so that the call will land on there...
  4. Monrovia

    change d42x02-config take effect automatically

    a star from me too! BR Monro
  5. Monrovia

    [L2QOS]

    hi satellite, Thanks for that setup. But the phones didn't take the vlan config and the new ip. however, it is taking all other settings like gatekeeper and stuff. I had to configure the phones manually... running to each desk :P BR. Monro
  6. Monrovia

    [L2QOS]

    Guys, please help me with this: I have the config file as below for the VLAN port configuration: [L2QOS] PhonePort=6,1 ;prio (0-7) ,VID(1-4094) PCPort=0,2 ;prio (0-7) ,VID(1-4094) LANPort=0,0 ;MAC based VLAN/802.1Q based VLAN , untagged/tagged PC originating traffic...
  7. Monrovia

    Auto attend IN MXONE.

    Ok. create a group GHGRI:GRP=XXXX,LIM=X,SERV=10000,TRAF=15,SEL=110000,QUE=5; GHGMI:GRP=XXXX,DIR=3840&&3843; RODNI:ROU=8,NIG=XXXX,DAY=9; this is for the night time and off duty PELPI:DIR=9,ANSPOS=9,CHO=1,BSYCHO=2,TIME=20; PELPI:DIR=9,ANSPOS=XXXX,CHO=2,TIME=20; this is for busy operators XXXX...
  8. Monrovia

    Auto attend IN MXONE.

    Hi Since there is no much info provided, the best & easiest way to answer this query will be GHGRI: CAT can be 01 or 15 (since it is extn to extn transfer) GHGMI: RODNI: Or else, pls post GHDAP:GRP=ALL; give a clue abt voicemail grp if any RODNP:ROU=XX; etc BR Monro
  9. Monrovia

    new number serie on MD110

    Hey, Did you end the ED series in NADAP? because, i found in your post about ending a route DEST. NANSE:NUMTYP=ED,NUMSE=321; ?? BR. Monro
  10. Monrovia

    h323 trunk adc

    Hi from ALEX LROUID= Local route identifier. The parameter states a route identifier used to distribute the incoming H.323 traffic. Incoming calls are distributed to that route whose local route identifier matches the route identifier received in the call. At the same time, the identifier...
  11. Monrovia

    h323 trunk adc

    Hi dont u miss 2 digits in ADC? BR Monro
  12. Monrovia

    Change operator to forward to an extension

    Hi jwhausk wrong place to post your request for help. This forum section is for AASTRA Regards Monro
  13. Monrovia

    DECT in MD110 TSW ?

    thanks for the info Doktor
  14. Monrovia

    BP Soft &amp; firmware download site

    Hi, that Russian forum is something different! If you use a translator (google translate) it is nice. They share everything there, even licenses!! Btb, Otoni, sharing the copyrighted software is against the forum rules... isn't it? Regards Monro
  15. Monrovia

    Onebox

    Oh yes, there is something wrong. how many call processors do you have? post a "print screen shot" thru imageshack.us of each call processor. and you are right, after leaving the message, the call will be terminated by saying "thank you for calling".

Part and Inventory Search

Back
Top