Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by KBBreakpoint

  1. KBBreakpoint

    NORSTAR - Any Way To Busy Out A Specific Line?

    This unit is call pilot capable but these folks won't spring for Caller ID cards when their employees are begging for it. Thanks for the suggestions
  2. KBBreakpoint

    NORSTAR - Any Way To Busy Out A Specific Line?

    Both good suggestions and ones I've thought of myself and I also didn't think there was any way to do this in a Norstar, they're too smart to let a line stay off hook like that. I'm going to suggest to the client these suggestions and let him make up his mind to do something or nothing. Thanks!
  3. KBBreakpoint

    NORSTAR - Any Way To Busy Out A Specific Line?

    Got a weird request from an old client: They have two lines (main and roll over line) and an old answering machine on the main line and the client wants people to get a busy signal if the answering machine is taking a message rather than rolling down to line 2. Is there any way in a Norstar to...
  4. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    Turns out the block was mislabeled. The issue WAS with the telco. Geez... The caller ID was set for all lines to be the main number so till I started pulling details of the block position from the carrier I had been looking at the wrong line. LOL!
  5. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    I moved the cross connect from line 1 to line six and vice-versa and I'm still getting the short delay on line 1 and 6-7 seconds on line 6. So it's not the incoming lines. Any ideas?
  6. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    The problem I'm seeing is really strange: Line 1 has no extra delay but lines 2-10 all have the longer delay. I checked the line programming and they are all the same.
  7. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    There is a delay longer through the MICS then off the 66 block. About 3 seconds off the block and about 6-7 through the phones Any ideas of what it could be?
  8. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    I had the same system in place and made no changes when they moved from a ADTRAN router with copper hand off to this Cisco one so I'm pretty damn sure it's not me. The only thing I could think of was the DTMF or something along those lines with the new carrier's box.
  9. KBBreakpoint

    Norstar MICS - Long Delay After User Dials Number

    I'm convinced this is a carrier issue but need to get some ideas just in case. Set up is that the carrier is providing a Cisco router with copper handoff lines. The lines are going into the MICS and on every phone are all ten lines. The end users hit a line not in use which gives them direct...
  10. KBBreakpoint

    COMDIAL DX-120 - Need To Change One Extension's Number Of Rings Before Sending to Voicemail

    I just talked with a Comdial engineer and on the DX-120 you can't do this. It's a system wide setting for the ring timer for an extension to voicemail. Only lines can be set to different numbers of rings.
  11. KBBreakpoint

    COMDIAL DX-120 - Need To Change One Extension's Number Of Rings Before Sending to Voicemail

    I've looked through every manual I can find online but can't find the answer to this. I have one extension on a system that the customer would like to have ring 10-12 times before voicemail picks up BUT would like all the other phones to answer after 4 rings. What I can do is change ALL the...
  12. KBBreakpoint

    877 Access and Configuration Issues

    Found the issue. The system was setting it's console port to 115200 rather then the usual 9600. Once I did that I was able to get in and was also able to get in using SDM.
  13. KBBreakpoint

    877 Access and Configuration Issues

    I've got a used Cisco 877 I got but I can't get into it at all. I did a factory reset by plugging it in and within 5 seconds pressing and holding the 'reset' button. I hooked up to it with a Cisco Console cable using putting (9600 8N1) but all I'm getting is garbage out of it even during...
  14. KBBreakpoint

    Can I have a BCM 400 email someone when a PRI goes down?

    THANKS A LOT. I got it and appreciate it! One question: It looks like this is the 4.0 MIB, is there any difference between that and the one for the 3.6 / 3.7 version? Is there a difference for the different BCMS? Again, I appreciate the help. Thanks!
  15. KBBreakpoint

    Can I have a BCM 400 email someone when a PRI goes down?

    How can I PM you, I don't see any way but I thought we used to be able to do it. How large is the file?

Part and Inventory Search

Back
Top