Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jdlrez

  1. jdlrez

    Star Talk Flash lost programming, no access

    The 266344 worked. We're in and rebuilding. Thank you to everyone.
  2. jdlrez

    Star Talk Flash lost programming, no access

    -If states Password then you lost ALL programming and msg's and need to start from scratch." That seems to be exactly the case. The manual I have states initial setup password for F 983 is 266344, but that may be something specific to the pbx's from J & J communications who's name is on the...
  3. jdlrez

    Star Talk Flash lost programming, no access

    It's a Flash. Not sure of software level. I will have them try f980 and see what happens.
  4. jdlrez

    Star Talk Flash lost programming, no access

    I need to preempt this post by explaining that I don't know anything about Norstar systems for the most part, I do not have physical access to the system. Unfortunately it falls to me to sort it out. The problem was initially reported to me as users being unable (all of a sudden) to access...
  5. jdlrez

    Need help diagnosing hardware problem

    Apologies for the vague subject, but since I don't know what's wrong, the best I can do is describe the symptoms. The 11c at a location I am working on is intermittently experiencing card failures. It began with the sole Analog card's red light turning on, causing all 500 sets to ring fast...
  6. jdlrez

    Replace M7310 with T7406

    Thank you, that sounds good.
  7. jdlrez

    Replace M7310 with T7406

    I would like to take out one of the M7310 sets at one of my locations and replace it with a cordless T7406. Is this basically hot swappable, or is there any sort of programming that needs to be done to the PBX? I am not concerned with programming specific buttons on the T7406, as all it needs...
  8. jdlrez

    Outbound caller ID on DID

    GHTROUT, In my testing, CID shows as "Unavailable" when making a local call (say calling my cellphone from my desk set.) We are a forms printing company so as far as I know there are no special circumstances. I am not entirely certain if our voice data uses our MPLS T1 circuit, a PRI, or...
  9. jdlrez

    Outbound caller ID on DID

    Hello all, I am wondering if it's possible to make only a single set which has a DID on it show up with a caller ID on outbound calls. Presently CID only works internally, all outbound calls to customers and the like show up blocked/no cid on their end. One particular employee has some...
  10. jdlrez

    Rolling to wrong voice mail box

    UPDATE: Got it, sorry to waste everyone's time. I did not think until after submitting, to look in the Voice Services menus in mermail. That was the problem. Thank you any way.
  11. jdlrez

    Rolling to wrong voice mail box

    Got a strange one here. The following set has 4 DN's mapped to it, 290, 223, 295, and 296. All but 290 have their own voice mail box (mermail) and different greeting. 223 and 296 both CFNA to their own mailboxes and greetings. 295 however does not. It rolls to an entirely different voice mail...
  12. jdlrez

    Changing unanswered call destination in ACD queue

    Gotcha. Thank you very much, again.
  13. jdlrez

    Changing unanswered call destination in ACD queue

    Telebub, Thank you, this worked. Of course I don't know how to record a greeting for a Menu Service, so right now after 30 seconds (I changed toft) an autobot says "No greeting recorded, transferring to operator" but that's better than nothing. Thanks again.
  14. jdlrez

    Changing unanswered call destination in ACD queue

    Telebub, Ok I did exactly that, created ACD 7004 (random unused DN) and set OVDN on ACD 550 (queue) to 7004. It let me do it, but my tests did not work. 2 of the 3 agents were in, the 3rd was on make set busy (lunch.) I had the 2 agents call each other to busy out their lines then dialed in on...
  15. jdlrez

    Changing unanswered call destination in ACD queue

    Ok, ran into another snag. I went into LD 23, did CHG, set OVDN to X and then went back in and tried to set it to 0 and got: SCH0707 DN conflicts with existing number. Does this relate to what telebub said re: " I believe the OVDN has to be an ACD number so create a dummy ACD and NCFW it to...

Part and Inventory Search

Back
Top