Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by hamncheese

  1. hamncheese

    I have a 4 node Rolm Mod 70 9751. I have to remove Node 4 in the next few days.

    Does the Mod 70 still have p-cnfg? You will probably have to delete the node 4 links
  2. hamncheese

    Automatic ringing line pickup when lifting handset?

    You might browse to the phone webpage and check the keyset features. There are terminating preferences in there for the IP55, It been a while but I think they are in there for the 410's and 420's too.
  3. hamncheese

    Openstage 40 SIP - VPN

    I use OSPE on my laptop. After I tunnel into VPN I activate the softphone.
  4. hamncheese

    one telephone two number

    you might be able to build a dnit to target the Prime exten on the phone. inbound routing only, pubnum would still be assigned to the Prime exten ADD-DNIT:DNI,2600,,,,NO,3400;
  5. hamncheese

    MWI to more than one phone

    In the 4000 you can use the MBLINE feature button for multiple MWI's. You'll need a line appearance of the extension on the assistants phone in addition to the MBLINE button. In OSV that feature is not supported so I set email notification in the XPR mailbox a send to a email dlist when a new...
  6. hamncheese

    Inherited PhoneMail SE 6.4

    There should be 2 IPL floppys. load the system using #1. the above procedure should work. Then type ? at the SVI prompt and you should get a list of commands. IPL floppy 2 has more commands and you may need to insert it in the drive if the reset password command is on # 2.. It's been quite a...
  7. hamncheese

    HiPath4000 ISDN PRI status "Ready/CP"

    Sometimes I've had to reset the d-channel to bring the circuit into service. Have you tried res-dssu:pen,1-2-103-0; Or sometimes only the b-channels using res-dssu:bchan,1-2-103-0,1&&23;
  8. hamncheese

    How to enable Telnet on HiPath 4000 V5

    Telnet comes disabled from the factory on later release 4 software and above. If the Telnet service is denied to the EIP the EIP will prompt you to run a Telnet Activation script in ComWin. To run this script, do the following: - Connect to the System using ComWin - From the Menu select...
  9. hamncheese

    Hipath 3500 System Kansas City

    pangeanetworks.com
  10. hamncheese

    IPDA and APE both drop out at the same time--network issue?

    Make sure no one has assigned the static IP's for your ipda and ape to something else.
  11. hamncheese

    Dis- Vegas ADS:status = SYSBRO

    Has anyone seen this before? I think the ADS status changed to SYSBRO after a unix corruption. Meaning System Broke. Can I just run amo <STA-DEL:":A1H1F:VEGAS/DATEI"; so I can regen RMX again? The system is a 4000 V5
  12. hamncheese

    Proposed acquisition of Unify by Atos

    Atos is a very dynamic company which has doubled its size & revenue in the last six years without debt, demonstrating an excellent track record in integration projects (e.g. integrating the IT Solutions & Services department of Siemens in 2011, acquiring European IT player, Bull, in 2014 &...
  13. hamncheese

    Xpressions Vogue script entry point in HiPath

    Vogue numbers have a DAR of TIE in WABE. They normally route to XPR through LDAT/RICHT 90.
  14. hamncheese

    MWI light stuck on HiPath 4000 v. 1 and Xpressions 3.

    Try signing off/on the phone using cha-dssu:signoff,STNO and cha-dssu:signon,STNO,PEN. Use dis-sbcsu first so you know what pen to sign back on to.
  15. hamncheese

    Backing up the hipath

    I use Donb01's backup server method because you can restore from the backup server if your network connection is there. I use NFS format and backup to a linux server. You can also go into the backup page in assistant and do a logical backup to the buffer. Then you enter comwin and go to unix...

Part and Inventory Search

Back
Top