Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by gbtac3

  1. gbtac3

    PRI cost increase

    We have been moving our customers over to Audiocodes M800C gateways. No changes needed on the SV9500, (besides swinging cables), and they support T.38. So far no complaints.
  2. gbtac3

    OPX card test

    Yes.
  3. gbtac3

    Callpilot App Builder Player issues

    Check you RPLs to make sure the number you are calling can be dialed. If memory serves me it's the desktop one that needs to be set, (but you may want to try a few others).
  4. gbtac3

    e911 on rls 7 where to start

    On release 7, ESA is configured in overlay 24, and a few other locations. I would read through the ESA documentation, but I would not mess with this without a partner for legal reasons. Even if you have to pay someone, it is better safe than sorry, especially here in the US, where there are more...
  5. gbtac3

    Replace M2250 Consoles with 3904 Digital Sets

    You cannot replace M2250 consoles with M3904 sets, but as @JTDubai directed, you can modify your system to send calls to another position. You will lose a lot of features of the attendant, so you may want to plan this carefully. Printing out your NIT and ATT data will give you an idea of what...
  6. gbtac3

    Callpilot 5.0 software

    It took forever, but I finally found it - Nortel_CP5[1].0_05.00.41.20_1005r_Image_1of1_Jan16_2007_517589578.ISO It's 2 GB. I am not sure how to get it to you. Ideas?
  7. gbtac3

    NEC IPK-I Moving from T1 to PRI

    Here is what I have in my notes, although I started working on the SV9100 and only rarely field calls for IPK. I am not sure if there is a specific license for ISDN/PRI, as I could not find one on the SV9100. ISDN-PRI 10-03-01 Leave set to T-Point The other options are not supported by the...
  8. gbtac3

    SV9100 CP10 Intermittent no outbound with SIP trunks

    I just had this same scenario. My solution was that I found more trunks defined in the SV9100 than enabled in the SIP carrier. I did not run any captures so I do not know if it is the same issue with the ports.
  9. gbtac3

    line

    @cheikhdtn - if you could detail the call flow, it will make it easier to give suggestions. Is this a call forwarded to the analog set from the console, etc..
  10. gbtac3

    DSS DCK-60-1P console

    Check out this link. It is for an SL2100, but they are built off of the same platform.
  11. gbtac3

    SEB Remote Monitoring

    There is a program called IRIS that is used to create sites and alarming. Unfortunately, the company just recently shutdown this product, so I would look at an alternative for alarm monitoring.
  12. gbtac3

    New to NEC PBX, need help with VM pw reset and some general questions

    If the system is using a GCD-VM00, then you are not using InMail, but you have a UM8000. You can reset passwords from a telset, as long as you login to voice mail using a mailbox that has system administrator checked. You can also change passwords via the web interface. The IP address for the...
  13. gbtac3

    sv9300 SIP TRUNK

    My lab is down so I have not confirmed my notes, but here they are - CLID Fields: CM08 379 462 507 524 539 563 584 603 736 1012 NOTE: When the second data of this command is set to 0 (Available), the second data of CM13 Y=69 must also be set to 0 (To provide) for My Line. CM12 20 56 CM13 69...
  14. gbtac3

    Caller id is not getting displayed

    This is old, but this was working in September 2002 - ADAN DCH 109 CTYP MSDL GRP 2 DNUM 8 PORT 3 DES CISCO.VG200 USR PRI DCHL 109 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC S100 SIDE NET CNEG 1 RLS ID ** RCAP ND2 T200 3 T203 10 N200 3 N201 260 K 7 ROUT 16 DES TKTP TIE NPID_TBL_NUM 0 ESN NO...
  15. gbtac3

    TTY - PMS connection not working - Nortel CS1000 Rls 7.0

    Print out your entire config in LD 22. Look under "PARM"?, (going off the top of my head), and look for PMSI. There are different settings and you may need to change those. I believe this protocol is async, so you may not be able to view it straight off the port. In LD 37 you can enl MSGI/ENL...
See more

Part and Inventory Search

Back
Top