Search results for query: *

On release 7, ESA is configured in overlay 24, and a few other locations. I would read through the ESA documentation, but I would not mess with this without a partner for legal reasons. Even if you have to pay someone, it is better safe than sorry, especially here in the US, where there are more...

You cannot replace M2250 consoles with M3904 sets, but as @JTDubai directed, you can modify your system to send calls to another position. You will lose a lot of features of the attendant, so you may want to plan this carefully. Printing out your NIT and ATT data will give you an idea of what...

It took forever, but I finally found it - Nortel_CP5[1].0_05.00.41.20_1005r_Image_1of1_Jan16_2007_517589578.ISO It's 2 GB. I am not sure how to get it to you. Ideas?

Here is what I have in my notes, although I started working on the SV9100 and only rarely field calls for IPK. I am not sure if there is a specific license for ISDN/PRI, as I could not find one on the SV9100. ISDN-PRI 10-03-01 Leave set to T-Point The other options are not supported by the...

I just had this same scenario. My solution was that I found more trunks defined in the SV9100 than enabled in the SIP carrier. I did not run any captures so I do not know if it is the same issue with the ports.

@cheikhdtn - if you could detail the call flow, it will make it easier to give suggestions. Is this a call forwarded to the analog set from the console, etc..

Check out this link. It is for an SL2100, but they are built off of the same platform.

There is a program called IRIS that is used to create sites and alarming. Unfortunately, the company just recently shutdown this product, so I would look at an alternative for alarm monitoring.

If the system is using a GCD-VM00, then you are not using InMail, but you have a UM8000. You can reset passwords from a telset, as long as you login to voice mail using a mailbox that has system administrator checked. You can also change passwords via the web interface. The IP address for the...

My lab is down so I have not confirmed my notes, but here they are - CLID Fields: CM08 379 462 507 524 539 563 584 603 736 1012 NOTE: When the second data of this command is set to 0 (Available), the second data of CM13 Y=69 must also be set to 0 (To provide) for My Line. CM12 20 56 CM13 69...

This is old, but this was working in September 2002 - ADAN DCH 109 CTYP MSDL GRP 2 DNUM 8 PORT 3 DES CISCO.VG200 USR PRI DCHL 109 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC S100 SIDE NET CNEG 1 RLS ID ** RCAP ND2 T200 3 T203 10 N200 3 N201 260 K 7 ROUT 16 DES TKTP TIE NPID_TBL_NUM 0 ESN NO...

Print out your entire config in LD 22. Look under "PARM"?, (going off the top of my head), and look for PMSI. There are different settings and you may need to change those. I believe this protocol is async, so you may not be able to view it straight off the port. In LD 37 you can enl MSGI/ENL...

What I have done to clean this up manually, is to go into the individual folders, (var/log, home and admin), and delete unnecessary files. These may include old log files and sometimes install and log files that were copied to home and admin for some other reason, (easier to transfer using...

If your system tries to track on the non-existent clock, it will fail and may go in to "Free-run" mode, (clocking on it's own processor). This can sometimes cause static if the clock signal between the CPU and the DTI/T1 are off. But, as you found, in most cases, this is carrier issue.

Ld 17 REQ: CHG TYYPE: PARM ... PMSI: Yes ... PORT 1 (enter the port number here) then enter through until you get the UDATA/PDATA. LD 22 PRT PARM (to check)

In CFN, PMSI is still set to 5. PMSI MANU PMS1 PMCR 100 PORT 5 XTMR 0 PTMR 0 NDIS 20

On the SV9500, you can use IPAN in PCPro and then monitor your specific type of sets. If you see that they all register with the same MAC address, then use @DoubleDriveLine procedure above. The issue is the device setting of the client and it needs to use the physical device and not the VPN.

Check you RPLs