Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Executor71

  1. Executor71

    Bcm 450 R6 - error with EICON DIVA card

    Hi there, i'm working on the same issue and on the same kind of products. I'm thinking about what you have written before (ECartman). 1 - why the public OLI can interfere with the ISDN communication (fro BCM to DIVA hardware) 2 - That's a good question, i'm sure that the route is configured as...
  2. Executor71

    BCM 400 - Password Reset

    Re Image your hard drive, in BCM 400 there's no reset procedures, those procedures are avaliable only on BCM 50 or BCM 450. bb ^^
  3. Executor71

    BCM OLI Length

    You have that difference because the public OLI, i'm speaking for EMEA, have 10 digits, you have to change the OLI when you have a DID feature active from your carrier. So, for example, my number is 022441xxxx where 022441 is the fixed part of the number, the rest is for the DID selection. The...
  4. Executor71

    bcm 400 3.7 i.p. 0.0.0.0

    If you have used the BIT for the 3.7 be aware that there is a known issue, apache crashes due a certification error, before starting the core upload procedure backup the cert folder on the bcm under apache directory, and replace it when the system finished the core upload. Bye
  5. Executor71

    bcm 400 3.7 i.p. 0.0.0.0

    Quote From the Initialise Menu" choose option 1 - "Initialise Universal Profile" and the wait a short time for the next menu to appear From the "MSC Initialisation Menu" choose option 3 – depending on HDD version this maybe "E1 MSC LOAD" for 3.01 and 3.5 and "UK MSC E1" for 3.6 Again depending...
  6. Executor71

    MOH wont play. using 8bit wav's under 5 megs.

    And remember to change in the feature tab on hold = Music (the default value is on hold = tones)
  7. Executor71

    CLID missing leading 0s

    Sry, just checked the issue, that patch is for CTI apps, the BCM send wrong CLID...
  8. Executor71

    Unable to access BCM400 via any interface

    * Anyway, the mainboard is a free Nortel retrofit, so any insta guy have to replace it with a new one. FOR FREE *
  9. Executor71

    BCM 400 WITH 4 MSPECIII CARDS MSPEC III NTBB80AC

    With 2 more PEC card you'll increase the apps (Voicemail, Faxmail, ecc.) and IP phone capabilities of the system. I'm Italian and we don't use some of the modules you've installed on your BCM but if we have a DTM PRI module installed with 30 lines active and more than 64 user in the customer...
  10. Executor71

    Unable to access BCM400 via any interface

    In any case the system have to give access to you via http or https, if the system is a 400 with a 3.0 release try to manage it via http://theipaddressofyourbcm:6800 The front left panel have several green led, when u power up the system, after 12 mins this leds have to become solid green, if...
  11. Executor71

    CLID missing leading 0s

    What is the version of BCM 50? (1.0 - 2.0 - 3.0) If i remember well there is a patch in the Nortel Website for a CLID issue, try to download and install the last service update.
  12. Executor71

    Caller ID over Voip Trunks

    There is a chapter on your BCM 200/400 called Network configuration guide, in this document you'll find how to configure the CLID properly into a VoIP trunk or into an ISDN configuration. Hope this will help you! Bye
  13. Executor71

    Connect I2004/I2002 to BCM50

    David, you have to check the DCHP settings on your BCM50 and the "allow registration" button in the IP sets resources. If the DHCP server, on your bcm 50, is DISABLED then configure the phone manually pushing the 4 button (from left to right) under the display when the phone startup. Bye!
  14. Executor71

    How to configure transfer restriction on BCM -400 3.7

    You have to configure the forward on busy on that set, and set in the capabilities the DND on busy on "Y".
  15. Executor71

    BCM Element Manager Remote Access

    I've the same situation, you have to open the 20-21-5989-60001 ports to have the element manager works. You have to open the 20-21 ports if you want to patch the system frome your home. Bye.
See more

Part and Inventory Search

Back
Top