Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Devanam

  1. Devanam

    4425 IP Phone Question

    Ok, thank you guys for your help. I found my issue. Some punk in my shop decided to leave a laptop's settings set to search for a Proxy server. Once I fixed that, I was able to log into the phone and changed the gatekeeper address. After I changed the address I was able to sucessfully log...
  2. Devanam

    4425 IP Phone Question

    OK, let me give you my exact situation, then hopefully you can assist me in solving this problem. I have a very basic configuration, and not much invested into it. I have a 2950t Cisco switch connected straight to the EL32 card. Then I have the 4425 IP phones hung right off that switch...
  3. Devanam

    Can't get "FollowMe" button to work on IP phone 4425

    How do I access and configure the form that Huxham references? Please help me. Thank you in advance.
  4. Devanam

    4425 IP Phone Question

    I am attempting to connect some 4425 IP phones to the EL32 card in my MD110. I have connected two of them and I am able to sucessfully make and receive calls. There are, however six phones that I can not get to connect. I have checked all my administrator's settings in the phones and they all...
  5. Devanam

    Installing TLU76/1

    Thank you for the assistance... The link I'm trying to establish is a tie line and not a pulic route. I tried to offset the ROEQI as suggested but this time it only allowed me to create 1 timeslot for the trunk before giving me the equipment error. Has anyone seen or heard anything to this...
  6. Devanam

    Installing TLU76/1

    Sorry it's been a while... Yes, I have more than enough licenses for the trunk. I do have other locations to move to card to. I have moved the card, and still the same issue. When I try to assign the equipment side of the trunk it is assigning two timeslots and then telling me that I do...
  7. Devanam

    MD110 Training

    Hello all, As of late I've been looking for advanced training in the United States for the MD110(BC11&BC12). It doesn't seem that Ericsson's facility in TX does anymore training for the MD110. The only places that I have located the training I am looking for is in Europe. Anyone have any...
  8. Devanam

    Installing TLU76/1

    Hello all, Recently I have been attempting to install a TLU76/1 into a BC11 MD110. The card installs, and I can program my ROCAI and RODAI on it. However when I attempt to program my ROEQI I get a message telling me that it completed partially. I check and I am missing timeslots 30&31. I...
  9. Devanam

    Short Call Time...

    My Company has two MD110s. One is BC11, the other is BC12. I'm trying to tie a trunk between the two. I have made the BC11 MD110 Master, and the BC12 MD110 Slave. My issue is that when the master MD110 calls the slave, the call only stays up for about 5 - 10 seconds. But, when the slave...
  10. Devanam

    7 to 4 digit dialing

    Thanks man! That was the issue. Guess I'll never overlook that again, you have no idea how long it took me before I even thought to post on here.
  11. Devanam

    7 to 4 digit dialing

    I have attempted that. Infact, I've tried all the NUMTYPs on all the CRVTYPs. None of them are working. Is there a possibility that it could be the way the trunk group is set up on my service provider's side? By the way, thank you for the speedy response.
  12. Devanam

    7 to 4 digit dialing

    Hi all, I seem to be having some number conversion issues with my MD110. Currently my service provider is sending me all 7 digits and I wish to truncate the first three digits in order to access the 4 digit internal dialing I have set up. The issue seems to be that no matter what paramiters...

Part and Inventory Search

Back
Top