Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Wierd Dialing issue

Status
Not open for further replies.

chicagophoneman

Programmer
Jun 22, 2004
151
US
Im scratching my head. I have a fax machine that when the user dials out the full number the system sends it aar over IP trunks but if the same user dial the full number from there digital phone it goes out the PRI. Is there something I am missing?
 
I wonder if the fax is inserting or deleting some digits. I have some that can. Other than that it may be COR/COS related. Set the digital set up with the same COR/COS and see if it still routes out the same way.

"A people that values its privileges above its principles soon loses both."
- Dwight D. Eisenhower (1890-1969), Inaugural Address, January 20, 1953

For the best response to a question, read faq690-6594


 
Have you done a 'list trace station xxxx' on the fax machine extension to see if its inserting or deleting digits?
 
Its putting in just the udp entry and sending it over the Ip trunks. I never see the full number. This is at a differnt site than I am at but I can hear more than our 5 digit dial plan being dialed but only see the 5 digits in the trace
 
If they are a different site they might be a different location (as in display locations) as well and they might use a different ARS Digit Conversion table than you are.

Regards

Frank
 
Nothing in digit conversion table and multiple locations not turned on in pbx
 
Two things you can check:

Tenant number of both phones, it's on the station form under: TN:

Check to see if the Fax machine is automatically programmed to dial 9 or some other number, hotline or ARS code...

Do the list trace station xxxx on both the fax and the phone then dial the number from each - and if that dosen't tell you what the issue could be paste the results from both traces so we can look at it...
 
You can take a single line phone and plug into the fax line. Then place a call and see how it routes out. If it routes like it should, then you know it has to be the fax programming.

"A people that values its privileges above its principles soon loses both."
- Dwight D. Eisenhower (1890-1969), Inaugural Address, January 20, 1953

For the best response to a question, read faq690-6594


 
Here is the list trace both dialed 9(ars) and the full number:

list trace station 63914 Page 1

LIST TRACE

time data

12:29:21 tone-receiver 01B0104 cid 0x1cf
12:29:21 active station 63914 cid 0x1cf
12:29:25 dial 13213 route:UDP|AAR
12:29:25 term trunk-group 98 cid 0x1cf
12:29:25 dial 13213 route:UDP|AAR
12:29:25 route-pattern 16 preference 1 cid 0x1cf
12:29:25 seize trunk-group 98 member 6 cid 0x1cf
12:29:25 Setup digits 13213
12:29:25 Calling Number & Name *****63914 Const. Fax, N
12:29:25 Proceed trunk-group 98 member 6 cid 0x1cf
12:29:26 Alert trunk-group 98 member 6 cid 0x1cf
12:29:26 G711MU ss:eek:ff ps:20 rn:1/1 10.5.5.105:2816 10.5.7.100:2908
12:29:42 active trunk-group 98 member 6 cid 0x1cf
12:30:24 idle station 63914 cid 0x1cf


list trace station 63655 Page 1

LIST TRACE

time data

12:44:24 Calling party trunk-group 98 member 1 cid 0x203
12:44:24 Calling Number &
12:44:24 hold station 63655 cid 0x203
12:44:27 active station 63655 cid 0x207
12:44:30 dial 91312751 route:pREFIX|FNPA|ARS
12:44:30 term trunk-group 1 cid 0x207
12:44:31 dial 91*****13213 route:pREFIX|FNPA|ARS
12:44:31 route-pattern 1 preference 1 cid 0x207
12:44:31 seize trunk-group 1 member 23 cid 0x207
12:44:31 Setup digits 1*****13213
12:44:31 Calling Number & Name *****63655 NO-CPName
12:44:32 Proceed trunk-group 1 member 23 cid 0x207
12:44:32 Alert trunk-group 1 member 23 cid 0x207
12:44:40 idle station 63655 cid 0x207
12:44:40 unhold station 63655 cid 0x203

I am at a differnt site but will get someone to connect an analog phone and do a trace and see what I get
 
The "9" wasn't captured on the first extension x63914. If it's being dialed maybe the "9" key is stuck or broken, or you may need to pause briefly and make sure you have dialtone before dialing:

x63914
12:29:25 dial 13213 route:UDP|AAR = [no "9" was dialed]

x63655
12:44:30 dial 91312751 route:pREFIX|FNPA|ARS
 
chicagophoneman
do a change station 63914 and check there is not an entry in the hotline feature on page 3 and see if it is looking at a speed dial list
Thanks
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top