What is the Process for setting up routing from a BCm50 to M1

[Bhargrove]

I am setting up least cost routing from BCM50 to M1. I have turned on messsging on the M1, I see the digits that are being dialed fromthe BCM, but I get a pause then fast busy after dialing the full number. Any help would be appreciated.

 

[biv343]

Are you sending the 9 to the M1? Have you changed your public prefixes to reflect the 9? for example, prefix default is 7 digits, or 10 digits depending on how many numbers you have to dial for a local call. If you're sending the 9 to the M1, then you'll only get 6 digits after the 9 before the BCM sends the call. Change prefix default to 8 or 11, and try that. You may need to change the prefixes for LD and international as well.

 

[Bhargrove]

yes I have changed all of that, when the digits get to the M1, I see let me give an example:

DCH 0 IMSG SETUP REF 00008001 CH 2 23 TOD 10:47:46
FEAT :NAS
CALLING #:5408988500 NUM PLAN: E164/NATIONAL (NPA)
CALLED #:5383577 NUM PLAN: E164/NATIONAL (NPA)

this is what I get on the M1, Even when I send a 9 across I still get a busy.

 

[pronei]

1. NRS at M1 site
2. H323 or SIP trunks on M1
3. M1 setup as gateway endpoint on NRS
4. Routing entries for M1 on NRS
5. CDP on M1 that include BCM50 DNs
6. BCM50 setup as gateway endpoint on NRS
7. Routing entries for BCM50 on NRS
8. Config BCM50 for H323 or SIP Trunks
9. Verify BCM50 registered to NRS
10. Build Routes & Calling plan on BCM50 to access VOIP Lines

Make calls!

Obviously there is a LOT of setup involved in each of those steps, if you need help with any of those steps, let us know.

 

[pronei]

Your not doing Network calling?

Well, scratch my post then!

 

[Bhargrove]

Please assist what is the process on the M1

 

[pronei]

How do you want the calls routed between the 2 systems?

Through PSTN (PRI) or Network (SIP/H323 Trunks)?

 

[Bhargrove]

Pstn(PRI)

 

[pronei]

Is the BCM a local or LD call from the M1?

When you make a local call, can u use 7 digits or is the full 10 digits required?

 

[tnphoneman]

Looks like you need to say yes to INAC on the route in the PBX. This will automatically insert the BARS access code in front of any number that is not CDP or UDP dialing numbers.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[Bhargrove]

The Bcm50 is long distance, but I am using a a Tie trucnk through Microwave to connect these systems together.

Also changed the INAC to yes, and that didn't make any difference.

 

[pronei]

Prt the route that you are using.

 

[Bhargrove]

TYPE RDB
CUST 00
ROUT 2
DES LOUISA
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00002
NCNA YES
NCRD YES
TRO YES
CHTY BCH
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR YES
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8802
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5


PAGE 002

TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 12
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

 

[pronei]

Now, in LD21
LTM
ROUTE 2

 

[Bhargrove]

YPE TLST
TKTP TIE
ROUT 2
DES LOUISA
TN 002 01 MBER 1 LOUISA
TN 002 02 MBER 2 LOUISA
TN 002 03 MBER 3 LOUISA
TN 002 04 MBER 4 LOUISA
TN 002 05 MBER 5 LOUISA
TN 002 06 MBER 6 LOUISA
TN 002 07 MBER 7 LOUISA
TN 002 08 MBER 8 LOUISA
TN 002 09 MBER 9 LOUISA
TN 002 10 MBER 10 LOUISA
TN 002 11 MBER 11 LOUISA
TN 002 12 MBER 12 LOUISA
TN 002 13 MBER 13 LOUISA
TN 002 14 MBER 14 LOUISA
TN 002 15 MBER 15 LOUISA
TN 002 16 MBER 16 LOUISA
TN 002 17 MBER 17 LOUISA
TN 002 18 MBER 18 LOUISA
TN 002 19 MBER 19 LOUISA
TN 002 20 MBER 20 LOUISA
TN 002 21 MBER 21 LOUISA
TN 002 22 MBER 22 LOUISA
TN 002 23 MBER 23 LOUISA




DES LOUISA
TN 002 23
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 30
RTMB 2 23
B-CHANNEL SIGNALING
TGAR 15
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 30 APR 2008

 

[pronei]

LD 60
Stat 2

What status are your channels in?

I've never networked a BCM50 to M1 before, only M1 to M1, honestly I'm not sure if it even works, but I'll do what I can to help.

 

[Bhargrove]

PRI* TRK LOOP 2 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 0
.****
OVL000
>ld 96
DCH000
.stat dch 0
DCH 000 : OPER EST ACTV AUTO
DES : Louisa

As you can see everything is up I have the voice mail working, I can do internal dialing, but I cant do external long distance over the tie

 

[hawks]

So you can call from system to system you just can not use 1 to go out another?

 

[Bhargrove]

that is correct

 

[acewarlock]

You have the trunk NCOS set to 30, can an NCOS 30 dial off the Option?????




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.