Larryataccess
IS-IT--Management
I already am setup so i can dial into get messages remotely but I would like to be able to dial in and run short codes like to set a huntgroup into night service and a number of there things. HELP!!!!!!!!!
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Remotly running short codes
- Thread starter Larryataccess
- Start date
- Status
amriddle01
Programmer
What release are you running? the first suggestion I made can also be made to work with older VM 4.1 etc...wth a little more work 
Are there no spare numbers at all in the sysytem that don't clash with extn or local dialling?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
Are there no spare numbers at all in the sysytem that don't clash with extn or local dialling?ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #22
Larryataccess
IS-IT--Management
I am good on spare numbers. I am not on 5 Yet. Amriddle i guess i did not totally get your idea
amriddle01
Programmer
Say you had numbers beginning 7 that would not match any other extn or local number you could use
shortcode 7xxx
Feature set HG night service
Tel number N
then transfer from VM to 7$key
the $key being set from a menu you create with a custom touch tone You follow?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
shortcode 7xxx
Feature set HG night service
Tel number N
then transfer from VM to 7$key
the $key being set from a menu you create with a custom touch tone
You follow?ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #24
Larryataccess
IS-IT--Management
I think i see the LIGHT!!! let me go push buttons
amriddle01
Programmer
The R5 callflow above will set the hungroup with the extn I enter in the menu into night servce
ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #26
Larryataccess
IS-IT--Management
created the 6xxx short code to turn it on and it worked and i created a 7xxx to turn it off and it worked but the VMPRO menu i built i did a menu option called ??? and then did a transfer to 6$KEY but it doesnt seem to work any ideas?
- Thread starter
- #27
amriddle01
Programmer
What happens when you make the selection in VM?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #29
Larryataccess
IS-IT--Management
nothing it goes dead air no beeps like the form a handset on system and it disconnects my call
Create a Menu two options 6 and 7 > connect it to another menu add the ??? > transfer it to 6$KEY and the other transfer to 7$KEY
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
amriddle01
Programmer
What does SSA and monitor show as happening, also debug trace could be informative
ACS - IP Office Implement
"What the Crocodile Hat....was that?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #33
Larryataccess
IS-IT--Management
i have the exact same but i did press 1 to activate nights and 2 to deactivat nights then went to a menu on each of them with a option ??? and then transfered to 6$KEY and 7$Key
amriddle01
Programmer
That shouldn't make any difference really....but can't hurt either
ACS - IP Office Implement
"What the Crocodile Hat....was that?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
amriddle01
Programmer
Can't you go to R5? Then you can just use my Pic above and you're set
ACS - IP Office Implement
"What the Crocodile Hat....was that?
ACS - IP Office Implement
"What the Crocodile Hat....was that?
- Thread starter
- #37
Larryataccess
IS-IT--Management
Neither works i did Start>menu with 1 2 > menus with $> transfers with 6$KEY and 7$KEY and all i get is dead air and it hangs up and the HG is still normall not in night service
You need 3 menu's
Menu1: option 6 and 7 (ticked)
Menu2: $ (Add it by pressing the + and tick it)
Menu3: $ (Add it by pressing the + and tick it)
Transfer1: 6$KEY
Transfer2: 7$KEY
Now Connect:
Menu1 option 6 > Menu2 > Tranfser1
Menu1 option 7 > Menu3 > Tranfser2
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
Menu1: option 6 and 7 (ticked)
Menu2: $ (Add it by pressing the + and tick it)
Menu3: $ (Add it by pressing the + and tick it)
Transfer1: 6$KEY
Transfer2: 7$KEY
Now Connect:
Menu1 option 6 > Menu2 > Tranfser1
Menu1 option 7 > Menu3 > Tranfser2
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
- Thread starter
- #39
Larryataccess
IS-IT--Management
i have exactly that setup right now but does not work
Try to add a "Generic" between the Menu2 and Transfer1 enter $CP0
And add "Generic" between the Menu3 and Transfer2 enter $CP1
Just like the picture Andy posted.
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
And add "Generic" between the Menu3 and Transfer2 enter $CP1
Just like the picture Andy posted.
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
- Status
Similar threads
