QSIG LINK BETWEEN MD110 AND CISCO CALL MANAGER NOT SENDING CALLER ID 1

[Njoro82]

Hi,

I have a QSIG link between cisco and md110 tsw7. The systems are calling each other well,calls from cisco are sending both the caller id and the number as expected. But i have a problem when a call is placed from MD110,as it is only sending the number without the associated name. What could be the problem?, here is MD110 config.

<ROCAP:ROU=10;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
10 7110000000000010 5 3100000001 0 30 128 03151515 511110000031 111111

<RODAP:rou=10;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
10 SL60 H'00000330 H'75440000 H'06300000 NO

END

<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
80 10 160610000000025000600110000 0 1


EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
63 4 - 24
71 4
72 4
80 4 - 4
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE

 

[BlAle]

Hi, Njoro82!
Please try:
RODDI ADC D5=2

 

[Njoro82]

Hi BlAle,

I used BC12 library (Alex)and noticed i had to change VARC (though they say not important in sl60,it works) and VARO settings,i changed varc to H'00000310 and VARO to H'55440000,but will try to change adc parameter,though with the above it works,

Thanks buddy

 

[BlAle]

It not to me.
I learned this nuance from my friend Nikolay Kuznetsov from Russia.

 

[Njoro82]

This is from Thomas(Aastra).And i agree with him,coz that what i changed and it works.

//Thomas

Hi,

One issue is for sure, that you are using UUI in the trunk settings. UUI can only be understood by other MX-ONE (BP). Also, you have set SERV D3 to public, which isn't good neither. I have tried to modify your parameters accordingly. You need to verify that for sure.

If it still doesn't help, a trace on SLP60 would be helpfull. With the Signal Trace interpreter from SAM, you can decode the ISDN messages and you can verify, whether GFP with name is sent.

Regards
Thomas


<ROCAP:ROU=10;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
10 7110000000000010 5 3110000001 0 30 128 03151515 511110000031 111111

END
<RODAP:ROU=10;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
10 SL60 H'00000330 H'50040000 H'04300000 NO

END

<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
60 10 160600000000025010600110100 0 1 0

 

[ceejay55]

have you set phones correcctly -see below from Cisco integration notes

To configure Calling/Connected Name and Number Restricted, use the following command:
<KSCACIR=1154&&1155,ADC=00010013010000;
To configure Calling/Connected Name and Number Allowed, use the following command:
<KSCACIR=1154&&1155,ADC=00100013010000;

 

[Njoro82]

Hi,
ceejay55;the problem was,i was sending UUI(Varc settings) infor to cisco,and seems like cisco could not decode that.I resolved this and now is working fine,I hadn also set Digital phones collectly
Thanks