PRI Trunks programming error sch0126 9

[Reveleo]

We are trying to program TIE trunks for a PRI2 card on a CS1000E. I have already programmed the DDB, CEQU, DCH, Net data, and RDB.
However, while attempting to program the 30 trunks in element manager or in LD 14, I receive err SCH0126: "Station type conflicts with existing card.For example: In LD 11, the craftperson has attempted to provision a digital set in the same IPE slot as an existing ITG card."

the system is as followed: the main cabinet is nummbered (4 0) and the expansion. so the first card in the main is 4 0 1
(the pri card is in our case in slot 1, so he is 4 0 1)

when we try to program the TIE trunk to TN 4 0 1 0, we receive above error..

the system is a CS1000E Release 7.5

Thanks,
Rev

 

[NoypiToits]

Please verify if the slot is empty...

REQ: STAT 4 0 1


Villareal

 

[Reveleo]

Hi Villareal,

yes, the slot is empty.. (physically it is in 1 slot, but was not programmed.. yet)

should i take it out of the slot as well?

Regards,
Rev

 

[GHTROUT]

Was there ever an analog or digital line card there? If so, try the LD10 or LD11 REQ OUT; TYPE CARDSLT or CARDMLT. Then add the trunk TNs.

--
Nortel Resources at GHTROUT.com World Famous!
--

 

[Reveleo]

No there wasn't .. it's a new install..

i do see that when you make your PRI2 loop, the system will add 2 units on that card (4 0 1 0 and 4 0 1 1). They are however unequiped when you do a stat on LD36 (the system does see them as digital trunks somehow)

Rev

 

[bhassell2000]

when you slide the card in or take it out do you get the XMI 4 0 1 to say a card was installed in the correct slot?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[Reveleo]

We took out the card and slided it back and got XMI002 4 0 1 PRI2
.. it does see it as a PRI2 card then right?

 

[bhassell2000]

sounds like it sees it as a PRI2 card. When you do a TNB or card inventory what does it show? I dont have scg0216 in my 5.5 or 7.5 books

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[Reveleo]

the error is SCH0126

we can't do a TNB on the card.. it does not see it as TIE or anything else so far..

 

[bhassell2000]

i have never seen a trunk on unit 0, can you build 4 0 1 1?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[PERRYPJ]

Unit 0 is the first on the card

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[Reveleo]

yes,Unit 0 is the first on the card

 

[GHTROUT]

PRI2 - so isn't the first TN 4-1?

--
Nortel Resources at GHTROUT.com World Famous!
--

 

[Reveleo]

The card is in the 1st slot in the 1st cabinet (shelf 0)
The system (CS1000E release 7.5) is using large format TN (l s c u). The Loop is 4. So the card is in 4 0 1.
The first unit is thus 4 0 1 0, the second is 4 0 1 1

Rev

 

[GHTROUT]

I see. I still think the TN is simply Loop-Channel, but I may be wrong in your case.

Since I'm unsure, I did find these helper threads:

thread798-1406456
thread798-1654738
thread798-1334840

If you post the Card Number/Model, I'd like to learn more about it - that might clear it up since we will find it in the book.

--
Nortel Resources at GHTROUT.com World Famous!
--

 

[bignose21]

Dont know what you are all on about but when you program a pri2 you put the number in the CEQU for example

PRI2 100
MG SLOT 4 0 1

When you come to do the channels it is
REQ new 30
TYPE tie
TN 100 1


Hope this helps

 

[bhassell2000]

ZBignose, I think thats what Gene and I were trying to get to. Good job!

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[bignose21]

L S C U is used (Tradionaly) in IPE (DLC, FALC, etc.). PRI is a network card an has Traditionaly been the Network Loop it is installed in and the Channel starting at 1.

So when the CS1000E started taking on tunks at release 5 they needed to come up with a way of maintaining the format, so you use a dummy network loop (Can't clash with Superloops in 97 or TDS/CONF loops in 17) and tie it to the card using CEQU. Then as before channels are on the network loop (Starting at 1).

 

[Reveleo]

Dear Gents,

so what you all are saying is, to make a "dummy" network loop and bind it to the card using cequ. The TN used when making the channels would than be with what format ( l s c u ) or (l u )

we tried to make the channels earlier by using the (l u ) format, but is does not accept this format.

i will try bignose21 advice.., but i believe that we did that already.. with the new software, you are indeed asked a loop and the MG Slot. (that goes fine). But when you make the channels by using the loop and unit (e.g. L U 100 1) it will say incorrect format. When you use the l s c u format (e.g. 4 0 1 1) it will say that the station type is incorrect ( see above error message)

we did notice that when you add the card to the system (e.g. after doing
PRI2 100
MG SLOT 4 0 1

the system will add 2 tn's (4 0 1 0 and 4 0 1 1)

Thanks so far gents.. Cheers! Rev

 

[Reveleo]

Gents,

we were able to bring the PRI up thanks to you guys.. Bravo..

The misleading TN , should indeed be loop and unit, so e.g. 100 1.
You have to start with channel 1 instead of channel 0.

Thats why the Tn 100 0 didn't work. it should have been 100 1

Cheers!
Rev