No Dial Tone after changes in LD 56: Opt 61C 1

[austin62]

Hello. On our Opt 61C, Rls 25.15, we made a change in LD 56 before the weekend, following instructions for turning off conference warning tone. Now our handsets have no dial tone. Can anyone tell me how to reversee the changes made, or apply the correct settings to reinstate dial tone? We only use first dial tone, before dialling the AC for an outside line.

This is the instruction followed in the first place, which resulted in loss of dial tone:

"Turn it off in ld 56

>ld 56


REQ chg

TYPE ftc

TABL 0

RING no

HCCT yes

ring=no
hcct=yes
cfwt=no

<ENTER> down to cfwt
xton=0

xcad=0

(You will only see cfwt as an option if it is not already set to default of 0)

This makes the tone and cadence for warning tone = silence.

It will not take effect until after midnight routines.

If instead you go to disable switch1, position 4 *set to ‘on’) on the conf card, be sure to disable them first and only one at a time."

The change took effect within an hour or so of the change being made - it did not wait for the midnight routines.

Also didn't have to change the cfwt setting as it was already set to 0


This is the FTC print afterwards, when dial tone had disappeared:

REQ prt

TYPE ftc

TABL 0

USER


TYPE FTC
TABL 0
NCAD 001
NBCS
XTON 002
DCAD 015
DBCS
XTON 002
ICAD 005
IBCS
XTON 002
RCAD 001
RBCS
XTON 002
GCAD 001
GBCS
XTON 002
HCAD 003
HBCS
XTON 002
PCAD 001
PBCS
XTON 000
XCAD 000
NDR1 PBX 002
NDR1 BCS
XTON 002
XCAD 002
NDR2 PBX 002
NDR2 BCS
XTON 002
XCAD 002
NDR3 PBX 002
NDR3 BCS
XTON 002
XCAD 002
NDR4 PBX 002
NDR4 BCS
XTON 002
XCAD 002
DIAL
XTON 000
XCAD 000
SPCL
XTON 129
XCAD 000
CDT
XTON 004
XCAD 000
CFDT
XTON 129
XCAD 035
MWDT
XTON 132
XCAD 017
CFMW
XTON 132
XCAD 017
BUSY
XTON 130
XCAD 030
RGBK
XTON 132
XCAD 032
ARBK
XTON 011
XCAD 002
FFCT
XTON 135
XCAD 000
ACTN
XTON 004
XCAD 000
HOWL 0027
LIMT
XTON 009
XCAD 002
NRMT
XTON 009
XCAD 018
AWUT
XTON 007
XCAD 017
OVFL
XTON 130
XCAD 000
TEST
XTON 008
XCAD 000
ERWT
XTON 003
XCAD 000
ACFT
XTON 003
XCAD 000
TLP
XTON 129
XCAD 000
TLPT 4
PATI
XTON 000
XCAD 000
EEST
XTON 003
XCAD 000
CAMP
XTON 137
XCAD 000
CDNC 017
ACBT
XTON 003
XCAD 000
CDNC 019
AOBT
XTON 003
XCAD 000
CDNC 018
CAB
XTON 043
XCAD 019
CDNC 019
INTU
XTON 133
XCAD 000
CDNC 036
CWT
XTON 003
XCAD 000
CDNC 020
OBKT
XTON 003
XCAD 000
CDNC 017
OVRD
XTON 133
XCAD 000
CDNC 036
OHQ
XTON 003
XCAD 000
CDNC 003
SRT
XTON 003
XCAD 000
CDNC 021
TMAT
XTON 003
XCAD 000
CDNC 022
TMOT
XTON 003
XCAD 000
CDNC 023
TSUT
XTON 003
XCAD 000
CDNC 023
ABST
XTON 004
XCAD 000
CDNC 208
PNNC
XTON 000
XCAD 000
CDNC 000
SRC1
XTON 000
XCAD 000
SRC2
XTON 000
XCAD 000
SRC3
XTON 000
XCAD 000
SRC4
XTON 000
XCAD 000
SRC5
XTON 000
XCAD 000
SRC6
XTON 000
XCAD 000
SRC7
XTON 000
XCAD 000
SRC8
XTON 000
XCAD 000
CFSN
XTON 004
XCAD 000
CPOQ
XTON 003
XCAD 000
RGAR
XTON 004
XCAD 000
RPCT
XTON 004
XCAD 000
RGAB
XTON 007
XCAD 000
MWAN
XTON 004
XCAD 000
DNDA
XTON 004
XCAD 000
SSLK
XTON 004
XCAD 000
P10 8
ID1 768
ID2 512
IDD 512
IDE 384
RVDL 0

Any help would be greatly appreciated.

Thanks

 

[phones1]

Alaw or Mulaw?

Remember if it doesn't work hit it harder

Scott UK

 

[austin62]

Thanks for getting back. You got me there though - should have also explained that my knowledge is seriously limited! If you can tell me what Alaw and Mulaw are and where I can look to answer your question, I will.

I would look it up but don't have access to the manuals today.

Thanks!

 

[phones1]

which country are you in?


Remember if it doesn't work hit it harder

Scott UK

 

[austin62]

Hello again.

We're in UK.

After a little hunt around I found some references to Alaw an Mulaw, checked ours and got the following:

>ld 22

REQ prt

TYPE atrn


ATRN
CODE 2
SOLR 7
ROLR +48.40
AOLR +37.35
TOLR -56.50
AGCD YES
VOLR NO
HRLR +42.00
HTLR -44.00


>ld 97

SCSYS000
MEM AVAIL: (U/P): 4150580 USED U P: 997801 143650 TOT: 5292031
DISK SPACE NEEDED: 251 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ prt

TYPE sysp


INTN = YES
QUIET CODE 0
THRESHOLDS 00004 00004
FLASH TIMERS 030 0130
TOHV 250
TDP 15
TID 150
TDPON 150
TPF 200
MFRL 2
XTRK MAKE/BREAK RATIO (PPS10) = 068
XTRK MAKE/BREAK RATIO (PPS12) = 050
XTRK MAKE/BREAK RATIO (PPS20) = 050
DEF (2006) 001
DEF (2008) 001
DEF (2216) 001
DEF (2616) 001
DEF (2000) 001
DEF (0500) 001
FNUM

FAST DOWNLOAD CONTROL TABLE

CARD TYPE DOWNLOAD OPTION VERSION TYPE VERSION #

XNET CONDITIONAL CURRENT **
LCRI CONDITIONAL CURRENT **
XPEC CONDITIONAL CURRENT **
XNPD CONDITIONAL CURRENT **
FNET CONDITIONAL CURRENT **
FPEC CONDITIONAL CURRENT **

Am I right that the ATRN setting is Mulaw and the INTN setting is Alaw?

Does this answer your question?

 

[phones1]

I normally follow the instructions below:


Overlay 56

[[[[[[[NOTE New or Chg depends if new switch or changing an old switch]]]]]

NEW or CHG

TYPE MCAD (Distinctive Ringing Cadence)
WCAD 15
CDNC 0080 0040 0080 0400

TYPE MCAD (Normal Ring - Internal)
WCAD 1
CDNC 0410 0800

TYPE MCAD (Camp-on Tone Cadence)
WCAD 35
CDNC 0020 0040 0020 1000

TYPE MCAD (Intrusion Tone Cadence)
WCAD 36
CDNC 0020 0400


Hardware Cadences

TYPE FCAD (Busy Tone Cadence)
WCAD 30
CDNC 0075 0075
END REPT
CYCS 1
SPCL NO

TYPE FCAD (Ringback Tone Cadence)
WCAD 32
CDNC 0080 0040 0080 0400
END REPT
CYCS 1 2
SPCL NO

TYPE FCAD (Call Forward Dial Tone)
WCAD 35
CDNC 0100 0100
END REPT
CYCS 1
SPCL NO

TYPE FCAD (Special Dial Tone)
WCAD 37
CDNC 0066 0006 0066 0006 9999 0000 9999
END REPT
CYCS 1
SPCL NO
-----------------------
LD 56
Ring Cadences

REQ chg
TYPE ftc
TABL 0
RING
HCCT yes
DIAL
XTON 129
XCAD 0
SPCL
XTON 129
XCAD 0
CFDT
XTON 129
XCAD 35
BUSY
XTON 130
XCAD 30
RGBK
XTON 132
XCAD 32
FFCT
XTON 135
XCAD 0
OVFL
XTON 130
XCAD 0


Software Controlled Cadences
REQ chg
TYPE ftc
TABL 0
RING
HCCT
SCCT yes
CAMP
XTON 137
XCAD
CDNC 35
AOBT
XTON
XCAD
CDNC
INTU
XTON 133
XCAD 0
CDNC 36
CWT
XTON
XCAD
CDNC
OBKT
XTON
XCAD
CDNC
OVRD
XTON 133
XCAD 0
CDNC 36





good luck & yeeeeeeeee Haaaaaaaaaaaaaaaaaaaa

Remember if it doesn't work hit it harder

Scott UK

 

[austin62]

Thanks! I'll get cracking and let you know how I get on.

 

[austin62]

Hello again.

Checked and adjusted settings as you suggested and just had confirmation from the site that we now have dial tone restored! No other reports of having broken anything else in the process, so looks like a big yeeeeeeeeeeeeee haaaaaaaaaaaaaa from me!

Only differences in the settings now are:

our CAMP we have CDNC = 17 (instead of your 35)

our FCAD WCAD 37 CDNC = 0066 0006 0066 0006 9999 0000 0000 (instead of your 9999)

Both of these are as they were before the problem came up, so I have left them as they are.

Monday looks better now - MASSIVE thanks to you!