ipo to ipo qsig 1

[PhoneDummie]

Folks,

Have never had to use Qsig so I need some much needed help.

Site A 406v2 - Dual PRI in Slot A - Single PRI in Slot B 5.0.18 (using single in B for Qsig) Slot A line 1 - local circuit / Slot A line 2 - LD circuit
Site B 406v2 - Dual PRI in Slot A - Using line 2 in Dual 5.0.18
no vcms - hence the pri cards and Qsig (customer had unused equipment)

Site A and B are 200 yards apart from each other - acquired bldg and customer wanted separate IP office for CCC (2 different departments). I have a CAT5e run between them with crossover T1 cable.

Need full gamut of how to set up the PRIs and shortcodes.

Extensions at site A 1xxx
Extensions at site B 3xxx

Any help is appreciated

 

[Bas1234]

Here is some info on my test once.

Licence;
ISDN30 module – PRI-Channel licence
IP500 Voice Networking licence (for Qsig)

ISDN30 Crosscable;
RJ45 RJ45
1 – wt/or 1 – wt/bl
2 – or/wt 2 – bl/wt
4 – bl/wt 4 – or/wt
5 – wt/bl 5 – wt/or

Settings Avaya:
ISDN30 – Line Sub Type = QSIG B
ISDN30 – CRC Checking = On
Incoming Call Route – Internal number
Short Code – Create a shortcode to the Qsig
Licence – Add licence

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[Bas1234]

PS, this was tested on a IP500 so double check if the licence is needed. Version was 5.0.18

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[tlpeter]

There is no need for the networking license on a 406!

Be sure that one site is set to QSIG A and the other to QSIG B!



Homo sapiens non urinat in ventum

honey, i fried the IP Office !!!

Sarcasm, it's only one of the services I offer.

 

[Bas1234]

Forgot to add that like tlpeter says.
And double checked the licence, for IP500 incl V2 need the licence.

QSIG A(master) QSIG B(slave)

This was a paste from my test connected to a Siemens HiPath.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[tlpeter]

Did it broke the Siemens ???




Homo sapiens non urinat in ventum

honey, i fried the IP Office !!!

Sarcasm, it's only one of the services I offer.

 

[Bas1234]

LOL, no it still works. The Siemens works as a SIP/ISDN30 router incomming/outgoing...

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[PhoneDummie]

tlpeter,

Site A is QsigA and Site B is Qsig B. Site A has three PRI cards ( 1 Dual and 1 single). The single I cannot set the line sub type to PRI.

 

[PhoneDummie]

ps - the dual has a Local and LD circuit in them already and both lines set to PRI. The single card I added is the one I cannot set to PRI.

 

[PhoneDummie]

Any Ideas?

 

[tlpeter]

You do not need it to set to PRI, you need to set it as QSIG which is not a PRI.


Homo sapiens non urinat in ventum

honey, i fried the IP Office !!!

Sarcasm, it's only one of the services I offer.

 

[dizzyphil]

send me your email address and I will get you a config that works.

Dizzy

ACA-IP Office Implement
ACS-IP Office Implement