Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Dialog 4422 IP Phone on MD110 Configuration 2

Status
Not open for further replies.

mheroy

Technical User
Jul 23, 2008
27
PH
Hi All,

I am installing a dialog 4422 IP Phone in a MD110 BC12/SP6. I got two(2) ELU Boards, 10 IP-extension licences, 3 VOIP-ETH-Interface.the Dialog 4422 is configured to BP-R15,how can I configure it to MD110?Any helpful configuration notes on how to initiate hte installation?

thanks in advance,
mheroy
 
You need to load a new Configuration file into the phones using a web server. The Config. file should then be edited so that the "System parameter section" is telling the phone that they now should work in an MX-ONE system.
 
Thanks!!

We have an IP network here, and I have a BMS Software.Where will I load it?will I load it in our server?What web server will I be needing?


mheroy
 
The BMS will be OK.
The phone directories should be stored directly in the root of the BMS server.
The BMS has a lot of good help text about FW updates of the IP phones.
 
Can I load the new configuration file directly to the phone?...
 
I have set-up the BMS server, but the IP Phone cannot detect the SW SErver,which is in tandem with the IP Phone.What seems to be the problem?..
 
There can be a lot of different reason for your problem:

1. Cross over cable between phone and PC?
2. Correct IP addresses entered in the Ip phone (SW server etc)?
3. You haven'm observed the fact that there are two HW versions of the phones.
4. You have wrong directory structure for the files on your PC.

Try open a browser on your SW server pc with the following address:
You should then see the config text.
 
I can view the configuration file thru the web address
I used a straight thru cable in tandem with the IP Phone.

I assigned the the PC's IP address as the SW server address of the IP phone.

Still the IP phone wont update.
 
Can you publish your config file in the forum?

 
something else if the phone is version 2 you need sp9 I think
 
Hod do you verify that the phone is not fetching the config file?
 
Every time I reboot the IP Phone, it wont upload.

This is the configuration file I am trying to upload in the IP Phone:


[System]
;--------------------------
; File: d4-config.txt
; Product id and version: CAA 158 0019 R5M
; Release date: 2007-08-15
;-------------------------
; The system parameter may have the values MD110, WEBSWITCH3, MX-ONE, MD-E, BP, BP-R15 and IMT
;System=WEBSWITCH3
;System=BP
;System=BP-R15
System=MD110 ; For ASB 501 04 (both MD110 and MX-ONE Telephony Switch)
;System=MD-E
;System=MX-ONE ; For MX-ONE Telephony Server
OverLap=YES
RRQTtl=600
GatekeeperID=LIM*
;Domain=ebc.ericsson.se
;PrimaryGKAddress=192.168.0.1
;SecondaryGKAddress=192.168.0.1
GatekeeperDiscovery=YES
AdminPasswd=RbdbSdc9c
CompatibleWithR3applications=NO
;LogOffRestriction=LogOffAllowed
;LogOffRestriction=DefaultNumberUsed
;LogOffRestriction=PermitIndividualLogOn

[Software]
;-----------------------------------------------
; The following files are mandatory:
; Bootrom d4-boot_Rev.dat (CAA158 0017)
; Application File d4-appl_Rev.dat (CAA158 0018)
; Configuration File d4-config.txt (CAA158 0019)
; The following files are optional:
; Language File d4-Lang_Rev (CAA158 0020)
;-----------------------------------------------

;Both DBC42201 and DBC42501 shall use same boot ,
;application and language file. It shall be stored
;in the dbc42501 directory.
HardwareRev=P1*
BootFile=/dbc42501/d4-boot_R5E.dat
BootVersion=R5E

ApplicationFile=/dbc42501/d4-applic_R5M.dat
ApplicationVersion=R5M

[Absence]
Profile=*10*profileNo#,#10#
FollowMe=*21*extensionNo#,#21#
ExtFollowMe=*22#extensionNo#,#22#
AbsenceReason=*23*reasonCode#,#23#
Lunch=0*hhmm
GoneHome=1
OfficialMatter=2*hhmm
Meeting=3*hhmm
Trip=4*mmdd
Illness=5*mmdd
FreeTime=6*mmdd
Course=7*mmdd
Busy=8*hhmm
Absent=9*hhmm
;Special=9*mmdd
;ParentalLeave=
;DayOff=7*mmdd
;Vacation=6*mmdd

[Authorization] ;replaces fthe following code with "-"
Code=*61* ;Account code for Standard Appl. System
Code=*72* ;Auth. code for Standard Appl. System
Code=*73* ;Lock Central auth. code
Code=#73* ;Unlock cent. auth. code
Code=*74* ;Change individ. ath. code
Code=*75*-*n# ;Dial with indiv. auth. code. n means that the nr will be visible
Code=*76* ;Lock individ. auth. code
Code=#76* ;Unlock individ. auth. code

[AutoNeg]
AutoNegLANPort=YES ;When AutoNeg is set to YES, Speed and Duplex will not
;DuplexLANPort=FULL ;be read. The resulting speed and duplex will be the
;SpeedLANPort=100 ;result of the negotiation between the phone and the
AutoNegPCPort=YES ;network device it is connected to(switch/hub/PC).
;DuplexPCPort=FULL ;Note.Not allowed to have a fixed full duplex-
;SpeedPCPort=100 ;connected to a device conf. for autoneg.

;[BackupGK]
;System=WEBSWITCH3 ;System=MD110 not allowed
;IPAddress=192.168.0.1

[Codecs]
; G.711 is mandatory but the priority order is optional
G.711A
G.711U
GSMEFR
G.729A
G.729AB
G.723

[DIFFSERVTCP]
TrafficClass=2 ;Class B
DropPrecedence=2 ;Medium drop percentage

[DIFFSERVUDP]
TrafficClass=5 ;Expedited Forwarding
DropPrecedence=3 ;High drop percentage, recomended for EF

[Display]
ShowDTMFDigits=YES

;[Emergency]
;System1=MD110
;Address1=192.168.0.1
;Port1=1720
;System2=BP-R15
;Address2=192.168.0.1
;Port2=1720
;EmergencyNr=112
;A-Number=077601
;RouteId=PASSW

;[FunctionKeysDBC425]
;CallBack=1
;FollowMe=2
;FreeOnSecond=3
;MessageWaiting=5
;Transfer=6
;Menu=
;Conference=
;CallPickUp=
;CallWaiting=
;Intrusion=
;HomeURL=10
;DirectoryURL=11
;EnablePBXStoring=NO

;[FunctionKeysDBC422]
;Conference=0
;Transfer=1
;Settings=5
;FollowMe=6
;MessageWaiting=7
;FreeOnSecond=8
;CallList=9
;CallPickUp=
;CallWaiting=
;Intrusion=
;EnablePBXStoring=NO

[Handsfree]
MicGainLow=NO ;May be used in small conference rooms. If it is set to YES and the
;current codec is NOT GSMEFR, the level of handsfree microphone and
;speaker output are lowered by 3 dB.
Loudspeaking=YES ;only for DBC422
StaticComfortNoise=NO


[Language]
;Default language is English. Optional languages can be selected
LanguageFile=/dbc42501/D4-lang_R5C.txt
LanguageVersion=R5C
OptionalLanguage=EN,*08*0#
OptionalLanguage=FR,*08*1#
OptionalLanguage=DE,*08*2#
OptionalLanguage=ES,*08*3#
OptionalLanguage=IT,*08*4#
;OptionalLanguage=SV,*08*5#
;OptionalLanguage=FI,*08*6#
;OptionalLanguage=DA,*08*7#
;OptionalLanguage=NO,*08*8#
;OptionalLanguage=NL,*08*9#
;OptionalLanguage=PB,*08*9#
;OptionalLanguage=PL,*08*9#
;OptionalLanguage=PT,*08*9#
;OptionalLanguage=XL,*08*9#
;OptionalLanguage=SK,*08*9#
;OptionalLanguage=CS,*08*9#
;OptionalLanguage=ET,*08*9#
;OptionalLanguage=HU,*08*9#
;OptionalLanguage=LT,*08*9#
;OptionalLanguage=SL,*08*9#
StartupLanguage=EN

[LEDs]
Cad0=185,5,5,5 ; LED flash 0 cadence, first on,first off,second on,second off: in a call
Cad1=50,50,0,0 ; LED flash 1 cadence: call parked
Cad2=30,30,0,0 ; LED flash 2 cadence: incoming call

[L2QOS]
MIIPort=6,1 ;prio (0-7) ,VID(1-4095)
PCPort=0,2 ;prio (0-7) ,VID(1-4095)
LANPort=0,0 ;MAC based VLAN/802.1Q based VLAN , untagged/unmodified PC originating traffic

;[OMD]
;SNAddress=192.168.0.1
;SNPort=1700

[RingCads]
Internal=20,100,0,1,0,0 ;Internal ring cadence
External=7,6,7,100,0,0 ;External ring cadence
Callback=6,8,6,8,0,0 ;Callback ring cadence
Extra=6,8,6,8,6,8 ;Extra ring cadence
Delay=7 ;Delay for MNS keys in second


[STOREPHONEBOOKS]
EnableStoring=NO

[SuffixServices] ;DBC422 only
Intrusion=8
CallWaiting=4
CallBack=5
CallPickUp=6

[Time]
TIMEZONE=CET:60:0:040101:110101
NTP-server=192.168.0.1

[Tones]
Dial tone=
0,0, ; One cadence, One frequency
500,0,0,0,0,0, ; 500ms on, 0ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0,
0,0 ; Tone in Voice is off, sine wave

Special dial tone=
1,0, ; One cadence, One frequency
500,50,0,0,0,0, ; 500ms on, 50ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

Busy tone=
1,0, ; One cadence, One frequency
500,500,0,0,0,0, ; 500ms on, 500ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

Alerting tone=
1,0, ; One cadence, One frequency
1000,4000,0,0,0,0, ; 1000ms on, 4000ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

Congestion tone=
1,0, ; One cadence, One frequency
200,200,0,0,0,0, ; 200ms on, 200ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

Special information tone=
3,4, ; Three cadences, Three frequencies
333,1,333,1,333,1000, ; 333ms on, 0ms off, 333ms on, 0ms off, 333ms on, 1000ms off
950,-10,1400,-10,1800,-10, ; 950Hz, -10dbm0, 1400Hz, -10dBm0, 1800Hz, -10dBm0
0,0 ; Tone in Voice is off, sine wave

Call waiting tone=
2,0, ; Two cadences, One frequency
200,600,200,3000,0,0, ; 200ms on, 600ms off, 200ms on, 3000ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

Offhook queuing tone= ;also used as verification tone for BP-R15
1,0, ; One cadence, One frequency
2000,990,0,0,0,0, ; 2000ms on, 990ms off, 0ms on, 0ms off, 0ms on, 0ms off
1400,-10,0,0,0,0, ; 1400Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off, sine wave

On hold tone= ; On hold tone
2 ,1, ; Two cadences, Two frequencies
10,150,10,5000,0,0, ; 10ms on, 150ms off, 10ms on, 5000ms off, 0ms on, 0ms off
400,-10,300,-10,0,0, ; 400Hz, -10dbm0, 300Hz, -10dBm0, 0Hz, 0dBm0
0,0 ; Tone in Voice is off , sine wave

External dial tone=
0,0, ; One cadence, One frequency
500,0,0,0,0,0, ; 500ms on, 0ms off, 0ms on, 0ms off, 0ms on, 0ms off
425,-10,0,0,0,0, ; 425Hz, -10dbm0, 0Hz, 0dBm0, 0Hz, 0dBm0,
0,0 ; Tone in Voice is off , sine wave

Waiting voice tone=
1,0, ; One cadence, One frequency
30,330,0,0,0,0, ; 30ms on, 330ms off,
425,-10,0,0,0,0, ; 425Hz, -10dbm0,
0,0 ; Tone in Voice is off , sine wave

[WAP]
WAPGateway=192.168.0.1
;DirectoryAddress=DirectoryAddress=192.168.0.1/MobileExec/default.asp
HomeAddress=wap.ericsson.com ; wapportal
;HomeAddress=MaxAttempts=3 ;2-8
RetransPeriod=2000 ;2000-7000
CountryCode=46 ;The code of the country where the PBX is located
RouteAccessNumber=00 ;The route access number
CountryCodePrefix=00 ;The prefix of the code of the country where the PBX is located
AreaCodePrefix=0 ;The prefix of the area code in the country where the PBX is located
 
Log on to the phone using a Web browser and verify what settings the phone is using.

Settings-->Show phone configuration.
 
This is the configuration file from the phone.

Configuration file
[System]
System=BP-R15
OverLap=YES
RRQTtl=600
GatekeeperDiscovery=NO
AdminPasswd=RbdbSdc9c
[Software]
HardwareRev=P1*
BootFile=/dbc42201/d4-boot_R3D.dat
BootVersion=R3D
ApplicationFile=/dbc42201/d4-applic_R3H.dat
ApplicationVersion=R3H
[AutoNeg]
AutoNeg=YES

[Language]
LanguageFile=/dbc42201/D4-lang_R3ABP.txt
LanguageVersion=R3ABP
OptionalLanguage=EN,
OptionalLanguage=FR,
OptionalLanguage=DE,
OptionalLanguage=ES,
OptionalLanguage=IT,
OptionalLanguage=SV,
OptionalLanguage=FI,
OptionalLanguage=DA,
OptionalLanguage=NO,
OptionalLanguage=NL,
StartupLanguage=EN
[Codecs]
G.711A
G.711U
G.729AB
G.729
G.723

[LEDs]
Cad0=185,5,5,5
Cad1=50,50,0,0
Cad2=30,30,0,0
[STOREPHONEBOOKS]
EnableStoring=NO
[DIFFSERVUDP]
TrafficClass=5
DropPrecedence=3
[DIFFSERVTCP]
TrafficClass=2
DropPrecedence=2
[WAP]
HomeAddress=wap.ericsson.com
MaxAttempts=3
RetransPeriod=3000
CountryCode=46
RouteAccessNumber=00
CountryCodePrefix=00
AreaCodePrefix=0
[L2QOS]
MIIPort=6,1
PCPort=0,2
LANPort=0,
0
[Time]
[Absence]
FollowMe=*21*extensionNo#,#21#
ExtFollowMe=*22*extensionNo#,#22#
AbsenceReason=*23*reasonCode#,#23#
Absent=1hhmm
Trip=2mmdd
Lunch=3hhmm
Meeting=4hhmm
Vacation=5mmdd
Illness=6mmdd
[Tones]
Dialtone=0,0,500,0,0,0,0,0,425,-10,0,0,0,0,0,0
Specialdialtone=1,0,320,10,0,0,0,0,425,-10,0,0,0,0,0,0
Alertingtone=1,0,1000,4000,0,0,0,0,425,-10,0,0,0,0,0,0
Busytone=1,0,500,500,0,0,0,0,425,-10,0,0,0,0,0,0
Congestiontone=1,0,200,200,0,0,0,0,425,-10,0,0,0,0,0,0
Specialinformationtone=3,4,330,30,330,30,330,1000,950,-10,1400,-10,1800,-10,0,0
Offhookqueuingtone=3,0,30,330,30,330,30,2000,425,-10,0,0,0,0,0,0
Callwaitingtone=1,0,100,4900,0,0,0,0,425,-10,0,0,0,0,1,0
[RingCads]
Internal=20,80,0,0,0,0
External=6,8,6,80,0,0
Callback=6,8,6,8,6,8
Extra=6,8,6,8,6,8
 
You write "I used a straight thru cable in tandem with the IP Phone" To rule out any cable issues, put a simple switch between SW server and IP-phone.
 
I have connected the IP Phone directly to the IP Network,still the Phone wont update...
 

Run Wireshark trace on the phone when booting up, this will tell you the file structure the phone is trying to get to on IIS server and if it is correct

BootFile=/dbc42201/d4-boot_R3D.dat
BootVersion=R3D
ApplicationFile=/dbc42201/d4-applic_R3H.dat
ApplicationVersion=R3H

best parnum
 
how can I change the status of the service state from passive to active?...
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top