Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Add a route and reboot the switch

Status
Not open for further replies.

lpchouinard

IS-IT--Management
Feb 3, 2009
18
CA
Hi, I am trying to add a route/gateway to the Call Server. From PCs on the 192.168.200.0 network I can ping the server (192.168.200.1) but when i try from the other side of the router i cant, it's not a permission/rule issue since i can ping other PC/CallPilot on the 192.168.200.0 network. I've read that you sometime need to do a INI on the server to have the settings applied, I have no clue how to do this... Here's what I've tried so far

For reference, Option 11c with 3 cabinets

CALL SERVER/MAIN CAB

VERSION 2121

RELEASE 3

ISSUE 00 +



LD 117



=> prt host

Call Server/Main Cabinet

ID Hostname IP Address

1 LOCAL_PPP_IF 137.135.192.4

2 REMOTE_PPP_IF 100.1.1.1

3 PRIMARY 192.168.200.1

4 SECONDARY 192.168.200.2

Media Gateway/Expansion Cabinet # 3

Host entry(ies) not found.

OK



=> prt route

Call Server/Main Cabinet

ID Destination Gateway Port

1 192.168.100.0 192.168.200.111 0

Media Gateway/Expansion Cabinet # 3

Route entry(ies) not found.

OK



=> enl route 1

LNK278 Enable ROUTE: "192.168.100.0" "192.168.200.111" failed.

OK



=> dis route 1

ROUTE: "192.168.100.0" "192.168.200.111" removed

OK



=> enl route 1

LNK278 Enable ROUTE: "192.168.100.0" "192.168.200.111" failed.

OK


I've also try the UPDATE DBS but with the same results

What am i missing here?

Thanks

Louis
 
You will have to bounce the ELNK in ld 137 then go back to ld 117 to enl the route.

 
the enl/dis of the ELNK did the trick, i was still unable to enl the route but the Server responding.

Thanks, you saved me some hairs
 
try adding new route 0.0.0.0 192.168.200.111
as the default route
 
WOW, i dont know what i ping when i said it work but it doesnt...

i tried with the 0.0.0.0 route and same result...

I can ping the ITG card but not the CallServer!?
 
Do a stat host in 117.
When you enl elnk in 137 does the IP addy match what is in the active host table?
Also do a prt elnk in 117 to check the active elnk addy
 
Yup it match, i realy dont understand this one...

=> prt elnk
ACTIVE ETHERNET: "PRIMARY" "192.168.200.1"
INACTIVE ETHERNET: "SECONDARY" "192.168.200.2"
OK

.stat elnk

ELNK ENABLED
Ethernet (qu unit number 0):
Host: PRIMARY
Internet address: 192.168.200.1
Broadcast address: 192.168.200.255
Ethernet address: 00:00:75:44:d9:11
Netmask: 0xffffff00; Subnetmask: 0xffffff00
297 packets received; 270 packets sent
0 input errors; 0 output errors
0 collisions
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top