Search results for query: *

Anyone with an idea about this? Anyone? Brian To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!

Looked on the AudioCode website and i do not find anything that would suggest that this is possible. does anyone know or have a working config for a remote office to use the SBC to make connection and register with the PBX that is behind the SBC. So in other words i have a PBX connected to an...

Ok next question. We are not using CUBE. So is the configuration the same???? Even though we are not using SCCP, do I associate the SSCP application to the profile????? Still not fully clear on that part To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!

Right....But as you can see, I dont see the hardware at all. I cant create a DSP farm unless the device sees the hardware. I have shutdown the router and reseated the DSP and the module to no avail. I do see this in the Show Run command that has nothing with it and have placed them into a dsp...

whykap, Yes I see them when i run the show diag command. PVDM Slot 0: 64-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card Hardware Revision : 4.0 Part Number : 73-8541-05 Board Revision : A0 Deviation...

I dont see anything that stands out. If I recall, there is normally a module name in the show hardware command. See below the output. Sprint5350# sho hardware Cisco IOS Software, 5350 Software (C5350-JK9SU2_IVS-M), Version 12.4(15)T3, RELEASE SOFTWARE (fc1) Technical Support...

I have a Cisco AS5350XM Router running IOS 12.4.15T3 and added 6 PVDM-264 in a module. When i look at the show voice dsp active, i only see 48 DSP. I think there is something i am missing like some configuration. I have looked around google and dont seem to find anything that can help point me...

thread940-1375906 ITSP says that they dont need a FQDN (Full qualified domain name) can you put the IP address in this field or do you leave it blanK??? Can you set this up without a FQDN??????? To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!

All, Have a customer that from time to time has to restart their phone system or the cisco router that we have on site doing a SIP to TDM ISDN-PRI handoff to them. it appears that the messaging between the 2 pieces of equipment seems to get messed up during an overnight time period and customer...

Jim, thanks for the reply. To answer your questions yes I work for the provider and am responsible for the Cisco router. What is being reported is that no inbound or outbound calls can be made or recieved. The settings on both seem to be fine. There are calls being passed between the router and...

All, Have a customer that from time to time has to restart their phone system or the cisco router that we have on site doing a SIP to TDM ISDN-PRI handoff to them. it appears that the messaging between the 2 pieces of equipment seems to get messed up during an overnight time period and customer...

Does anyone here know anything about Broadsoft Sylantro softswitch???? We are on an older version and have trouble with failing over from a nonresponsive gateway to a working gateway on the same call. Willing to pay someone a contractor fee to assist in resolving issue. Send me a PM Brian S...

All, I am using a Cisco IAD2431-8FXS with IOS software version 12.4.12. Is there a command that will allow me to test an outbound call thru a VoIP dial peer. I know about csim start <phone number> but that does TDM only not Voip. thanks for the help To error is human.....if the machine doesnt...

I would recommend Lightyear. they have good rates and good service. www.lightyear.net To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!

Does anyone have a working configuration for getting T38 to work when faxing outbound/inbound using an analog voice port on a Cisco IAD2431-8FXS. We are using 12.4.12 IOS software. I have included my current configuration for this device below. I am able to fax fine except when it is longer than...

I am looking for some help. We currently have 3 floors with phones on each floor. each floor is assigned a IP address range for the phones in our DHCP server. On the DHCP server it tells the phone the tftp server location to get the config file for the phone. When the phones come to the TFTP...

trying to avoid having to setup a different TFTP server. Any other ideas on how I could accomplish this????? To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!

Is it possible to have a phone look for a specific .cnf file based on the IP that was assigned during DHCP????? What I am wanting to do is if the IP address is say 192.168.1.xxx to get MGCDefault1.cnf and if the IP address is say 192.168.2.xxx to get MGCDefault2.cnf..... I want a certain range...

We are deploying IAD2400 series routers using 12.4.12 software version on customer sites to provide analog and PRI services. We have a Sylantro softswitch as our CO for these customers. We are having trouble offering reliable T.38 faxing as it appears that sometimes it works and sometimes it...

guys This is a Norstar MICS system. If you have any more specific info that can help, it would be greatly appreciated!!!! Brian To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!