Search results for query: *

Does anyone know where I can get a copy of the Nortel Remote Office Connectivity Manager software used on the 9150's and Reach Line Cards? I am trying to reconfigure, and can not find the software. Thanks.

Thanks everyone. I feel I am getting closer. After adding the s??? to my shortcode that redphone suggested, I am getting the area code to show. Now the problem is the rest of the number quit showing. I am receiving just the 3 digits I added. Any suggestions to append the rest? Thanks again.

How do you configure the National Number? Below is the output: 479179mS ISDNL3Tx: v=5 peb=5 ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0052(Remote) Message Type = Disconnect InformationElement = CAUSE 0000 08 02 80 90...

What do I need to do to show status of other extensions on a receptionists phone? She has a 24 button phone, and would like to have some of the buttons show if certain people are on the phone (like a blf). Thanks.

I have an IP Office installed with a PRI. The PRI provider (MCI) is delivering 7 digits. When I dial out, the caller id only shows the 7 digits. Is there a short code I can add to prepend the area code? Thanks.

I know this thread is quite old, but did you ever get RADIUS to assign the ip addresses by group. I am currently doing the same thing as you have outlined, and do not want to re-invent the wheel. Thanks in advance.

Thanks for all of the responses. I have made multiple attempts at the above routine. I am not getting any response from the IP Office on any AT commands sent. Also note, that it is showing the Multi-Sector Erase message on boot up, without sending the at commands. Also, I have scanned the...

I am very interested. I am currently being told by my vendor that the only option is to buy a new 406 since the other one is not under maintenance. I don't find this as a good option since the unit is only 13 months old and the Avaya IP Office - Job Aid was followed step by step. The vendor did...

I have an several IP Office 406's. I am in the process of upgrading them to v2.0. The first 3 upgrades went well, but the 4th one did not. It made it through the config erase, but failed the upload, so now it has no config. I have connected to the DTE port at 38400 8-N-1, and rebooted. I get the...

Found the problem. First off, I did not have the correct Filter set to see all traffic. Secondly, MCI was sending Inbound ANI, *, DNIS, *. So in total I was recieving 16 digits, and the IP Office had no idea what to do with them. I had MCI strip the ANI and *'s, and it is working fine. Any idea...

Primarily in the SouthEast and MidWest. This seems to be standard pricing from local telcos (SBC and BellSouth) for PRI, DID's, mixed-use with 512k to internet. Thet are providing the drop and insert mux.

Is anyone using Compact Contact Center? Is there an evaluation copy available. I have a small call center set up, and would like to be able to get simple statistics and reports. Any help would be appreciated.

At several small offices I am using PRI circuits provisioned with 8 - 16 voice channels with the remaining channels used for internet connectivity providing a VPN connection to our corporate office. This has turned out to be a very cost effective solution (usually $600 - $800 monthly), and still...

Sorry, I should have mentioned it is not a PRI, but a dedicated Long Distance T1, B8ZS/ESF, E&M Wink, 4 digit DNIS enabled. Below is a cut and paste from my monitor: 655663mS PRN: T1 Channel: E&M 1.1: Receive T1EMOffHook 655663mS PRN: T1 Channel: E&M 1.1: EventRx T1EMOffHook state=Idle...

Hello all. I am having problem with an IP Office and DNIS. I have the 4 digit DNIS programmed into the MSN, but when using monitor it does not seem to be receiving. I have had MCI test, and they confirm that they are sending. Any suggestions? I have the MSN programmed w/ 4 digits, including the...

I keep getting the following error: Task Summary: Move Mailbox Started: Thursday, September 12, 2002 12:04:48 AM Finished: Thursday, September 12, 2002 12:04:52 AM Results: Error: Connecting to source server. CN=New User,DC=bxgcorp,DC=com: The attempt to log on to the Microsoft Exchange...

The nic is PXE compatible. I get to the first screen of remote install, and the keyboard doesn't function. Num Lock or Caps Lock will not even light up the LED's. I have tried a non-usb IPAQ w/ the same version of Intel PXE driver, and it boots fine. Thanks for any help.

I am trying to use RIS on Compaq IPaqs with USB mice and Keyboard, and it doesn't seem to support it. Any help would be appreciated.