Search results for query: *

i normally do this (ONLY WITH SERIAL CONSOLE CABLE !!! ) enable config t wr erase reload (follow the config)

so it would be: access-list 101 permit ip 192.68.135.0 255.255.255.0 10.21.1.0 255.255.255.0 ip local pool ippool 10.21.1.1-10.21.1.254 vpngroup xxx-vpn split-tunnel vpnclient access-list vpclient permit ip 192.68.135.0 255.255.255.0 10.21.1.0 255.255.255.0 ?

so that would work if i wrote this: access-list 101 permit ip 192.68.135.0 255.255.255.0 10.21.1.0 255.255.255.0 ip local pool ippool 10.21.1.1-10.21.1.254

1 - i only get one ping though, when i try to ping the server on the lan, from my remote vpn client 2 - what do i need to change, if i want the remote VPN users to get a 10.21.0.x network instad of the 192.68.135.x this is the reply Pinging 192.68.135.14 with 32 bytes of data: Reply from...

hi. Im reinstalling a old PL3000 with a Dual-Channel Wide-Ultra SCSI-3 Controller. but there is no driver on HP's site. Does any of you guys have it?

Found out it was a activation key issue - i mailed licensing@cisco.com and they fixed me a new key in less than 15 minutes --- they are the BEST

Hi When i type in my 50user licens, my 3des get deactivated. And if i then retype the 3des, my 50 user become a 10 user why?

you are to cool :-) thanks a million, dont know why I dident get that line with me, when made that config. I need to buy that solarwinds pix-editor. just wasted 4 hours on that mistake ...

Hi I have set up this new Pix 501- I get prompted for the username and password, and i get validated through Radius, but i cant access the LAN. This is my config PIX Version 6.3(4) interface ethernet0 10baset interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1...

it gives me this: sakmp_process_block:src:217.157.148.85, dest:212.112.164.202 spt:500 dpt:500 ISAKMP: reserved not zero on payload 5! ISAKMP: malformed payload ISADB: reaper checking SA 0xac092c, conn_id = 0 ISADB: reaper checking SA 0xae665c, conn_id = 0 ISADB: reaper checking SA 0xab0d64...

I have a site with 5 locations. The Site-2-site is running fine, but the the client cant connect with the remote clinet. I have configured the IAS server like this: IAS -> remote acces policy -> Connections to other access servers -> Authentication: Only checkmark in pap, spap Encryption...

Found it myself: in enable you write wr erase (confim) reboot (confim) Then follow the guide

What command do i type in the console, if i want to reset the router to factory default?

the PC's is not a problem (Running DHCP) the servers will take 3 minutes to change with a VBS script in a policy. The Printes on the other hand will take forever :-(

wouldent it be better to change the lan subnet to 255.255.255.0? I mean, if i change the lan like this: Sweden: IP : 192.168.1.1-255 SN : 255.255.255.0 GW : 192.168.1.254 (router lan) Denmark: IP : 192.168.2.1-255 SN : 255.255.255.0 GW : 192.168.2.254 (router lan) Regards Kristoffer

Do you have a sampel of that? The current LAN is like this: Sweden: IP : 192.168.1.1-255 SN : 255.255.0.0 GW : 192.168.1.254 Denmark: IP : 192.168.2.1-255 SN : 255.255.0.0 GW : 192.168.2.254 Dont i have to change the Subnet mask to 255.255.255.0 when i make all the tunnels?

Do you have a sampel of that? The current LAN is like this: Sweden: IP : 192.168.1.1-255 SN : 255.255.0.0 GW : 192.168.1.254 Denmark: IP : 192.168.2.1-255 SN : 255.255.0.0 GW : 192.168.2.254 Dont i have to change the Subnet mask to 255.255.255.0 when i make all the tunnels?

Hi Im trying to set up the following: http://sparmere.dk/cisco/cisco.gif All the local sites should be able to se the Mainsite "bsn-sverige" and all the other local networks. I cant get the pix's to work. If any of you have a running config of the mentioned, please show it to me so I can learn...