Search results for query: *

Hello there, NBAR will be the way to go, on that lan connection enable nbar protocol discovery : ip nbar protocol-discovery after few min do : sh ip nbar protocol-discovery this way you will see what other types of traffic is taking out your valuable bandwidth. Next is to apply a policy map...

Hi all, I need a bit of help trying to get my head around this issue. Just a simple hub and spoke topology with 4 routers, r4 hub and r1,2,3 spokes all fully mesh at layer 2 using main int only. sh frame pvc | = will bing all the pvcs up active, if I enable frame on interfaces I am able to ping...

Hello there, to be able to move forward we will have to ignore any LED lights and try to send the unit into rommon mode it looks like the montherboard get initiated and we may have a bootstrap image (rommon). Whithout doing all possible to break into rommon mode there is nothing much else we...

Hello there, you will need to send the router into rommon mode. Reload and within 60 sec press ctrl break on your keyboard to send the router into rommon mode. Once in there check the following commands: meminfo to see if your main mem is ok and how big it is dev to list all the devices...

Hello there, do you have enough main memory to run the newer image? If you do please paste in here the output of the initial booting and the boot statement commands you have in your config... Cheers and good luck

Hello there, just go into conf t mode and type in no ip domain lookup exit and save.... Good luck

Hello there, you can give it a go using: http://www.devx.com/security/Article/21144/0/page/8 Cheers and good luck!

Hello there, can you paste in here the output of show mem sum only the first 3 lines and sho proc cpu? Also, it will be a good idea to clear the counters and capture a show int to see if any of your interfaces has lots of activities....

Hello there, for this issue there is a Cisco Field Notice. You will need a CCO account to have access to the information. http://www.cisco.com/warp/customer/770/fn7771.shtml Just to let you know that you will be able to use 12.0S bootimage which will support higher main IOS images thus...

Hello there, sorry I was off the net for a while.... Can you please let me know if you still have the issue? If so just add the command ip accounting on that interface and after few min do a sh ip accounting, this way we should be able to identify any suspect traffic or which source downstream...

Hello there, there is a way to tell the router to look for the bootflash in normal flash. I will do some research and let you know.

Hello there, you can remove a single file/image from flash too... Just to a sh flash identify the image you need to remove. Next: router# delete fash:<image name> pls not no space between flash:and the image name. router#squeeze ( this command will remove any images/files marked for...

Hello there, do you still need help on this issue? If so just let me know and I will try to help out. Cheers and good luck

Hello there, what a shame to see the replacement router fail. Did you try to use a different router platform? Maybe there is a software defect which applies to your existing platform. Did you try to use a different IOS? Also, can you post the errors you are getting now? Where abouts are you...

Hello there, This info may help as I could see a big no of throttles: Throttles - When the Input Q (process switching) fills up on an interface, the CPU assumes that something is misbehaving on that interface (broadcast storm, SNMP storm) since the processor is not able to keep up with the...

Hello there, as the router is getting hotter the power supply connection will become flackier thus the issue... If you have a hardware contract with Cisco you should be eligible for the replacement of the motherboard and the power supply unit. Cheers and good luck

Hello there, The errors are generated by a malfunction in your power supply, which sometimes doesn't make a good contact with the motherboard power connector, leading to low voltage on the motherboard thus the voltage on the network module will be too low to operate. You will need to replace...

Hello there, not a problem. Looking forward to your next post. I hope that the replacement router will fix the issue. Cheers and all the best!!!

Hello there, There are no hardcode limit to the no of gatways on a gatekeeper. However the main limitation will be the amount of existing main memory used to keep the gateways and endpoint info which are dependent on the name and e.164 address. If you are interested in how many E.164 address...

Hello there, the day just strated here... Ok, there are few issues we can look into it: 1. Run a debug ntp packet on client and look for the following: leap 3 on the client, the value should be leap 0 leap 3: alarm condition (clock unsynchronized). 2. For the client to be able to sync...