ok, so i have configured the Linksys Wireless router in Gateway mode, configured it with LAN IP 192.168.1.2, handing out DHCP addresses between 192.168.1.100-192.168.1.110 and can ping the 2811's FE0/1 interface at 192.168.1.1, however I cannot get online. I've tried an X/0 cable and a regular...
ok, i have configured FastEthernet 0/1 to have the 192.168.1.1 successfully. I plugged the Linksys WRT55G wifi router into the FE0/1 port on the 2811 with an X/O cable.
My question is what this: since the WRT55G is by default an actual router, it is wanting me to configure the Internet...
Nice. That's exactly what i was envisioning, just didn't have the confidence to try it out. This is a live corporate router, and the last thing i want to do was potentially knock it offline.
I would like to connect a Wifi Access point to FE0/1 and have it give out 10.x.x.x addresses to...
thanks for the response. I was wanting to do what you suggested, but on FE0/1 but it doesn't seem to be configured. What commands do I need to give the router to "activate" that port?
I am new to the world of Cisco Hardware and am trying to figure out how to set up a VLAN at our corporate office. Our setup consists of a Cisco 2811 Router, PIX 501, and a pair of Dell PowerConnect 3348 switches.
I would like to be able to use Cisco SDM to manage the router's configuration...
I've got a Dell Poweredge 2500 which can house 6 total hard drives. It's got a PERC 3/di internal embedded RAID controller which currently has 3-36gb SCSI drives configured in a single RAID-5 container.
I would like to add some additional HDDs to the system, and read on Dell's support site...
the thing is that I know the telnet/admin/enable passwords and have verified all of them to be working. I don't want to have to take the PIX offline to do a PW reset when I really have access to it. I just would like to be able to get into the PDM interface remotely because it would make my...
hey, thanks for the input, unfortunately that doesn't work for me. I didn't set this pix up, so I'm wondering if whoever did reset it to something other than the default.
next ?, how do I reset the GUI userid/pw?
i'm trying to login to one of my client's PIX501 GUI. I know the telnet, admin and enable passwords, but none of them work. I've also tried pixuser/cisco and vice versa. Nothing works. What is the default userid/pw combination for the GUI? If that doesn't work, how can I reset the GUI...
Hey KiscoKid, thanks for the response.
i've added those commands and they seemed to go over just fine. my question now: do I need to reboot the pix to get them to take effect?
this is what i've been trying:
access-list acl_out permit tcp any host 192.168.0.25 eq 5900
however, when I type that command, I get Type help or '?' for a list of available commands.
what am i doing wrong?
Hi everyone, i need a little help figuring out how to add a rule to my firewall config. Our company has a PIX 501 running v6.3(3) and Cisco PIX Device Manager Version 1.1(2) Anyway, I need to open up port 5900 for Remote access via VNC. If my external IP is 1.2.3.4 and the internal IP i'm...
i am trying to enact the 'blackhole' method as described by gmcdonnell and am running into problems with step 2.
i have created a universal mail enabled distribution group in domain.local and then i go into Properties/Email Addresses tab to add the addresses of my ex-employees and i get the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.