austinringding
Technical User
I am new to the world of Cisco Hardware and am trying to figure out how to set up a VLAN at our corporate office. Our setup consists of a Cisco 2811 Router, PIX 501, and a pair of Dell PowerConnect 3348 switches.
I would like to be able to use Cisco SDM to manage the router's configuration, but can't seem to figure out how to do that. I can connect via Console with no problems, and have downloaded SDM .zip package from the Cisco website, but I can't figure out what the internal IP address is of the router. The internal IP address of the PIX is 192.168.0.1. I know it's a silly question, but I can't figure it out.
Here is the output from Show Run on the 2811:::
------------------------------------------------------------
Current configuration : 1331 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname twtc-router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$4d0s$Ywvr3h34MPNy.7tZ7x0wl/
!
no aaa new-model
!
!
ip cef
!
!
!
username admin privilege 15 secret 5 $1$IC2H$C4aw2Gee5s9Cb.jU8d2pk0
!
!
!
!
interface Multilink1
ip address 168.215.163.94 255.255.255.252
ppp multilink
ppp multilink fragment delay 500
ppp multilink group 1
!
interface FastEthernet0/0
ip address 216.85.198.81 255.255.255.248
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
no ip address
encapsulation ppp
no fair-queue
service-module t1 timeslots 1-24
ppp multilink
ppp multilink group 1
!
interface Serial0/1/0
no ip address
encapsulation ppp
service-module t1 timeslots 1-24
ppp multilink
ppp multilink group 1
!
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 168.215.163.93
!
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
password 7 14391D5A272A253C37
login local
transport input telnet
line vty 5 15
password 7 14391D5A272A253C37
login
!
scheduler allocate 20000 1000
!
end
---------------------------------------------------------
I am also trying to follow the instructions at
to get SDM up and running, but am having issues with some of the commands.
For example, I can't run show webflash:
I get a Invalid input detected at '^' marker. message.
I also cannot add ip http secure-server to the config. I get the same Invalid input detected message.
As you can tell, i'm new to all of this stuff, but a fast learner if someone out there can lead me in the right direction.
Thanks in advance!!
I would like to be able to use Cisco SDM to manage the router's configuration, but can't seem to figure out how to do that. I can connect via Console with no problems, and have downloaded SDM .zip package from the Cisco website, but I can't figure out what the internal IP address is of the router. The internal IP address of the PIX is 192.168.0.1. I know it's a silly question, but I can't figure it out.
Here is the output from Show Run on the 2811:::
------------------------------------------------------------
Current configuration : 1331 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname twtc-router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$4d0s$Ywvr3h34MPNy.7tZ7x0wl/
!
no aaa new-model
!
!
ip cef
!
!
!
username admin privilege 15 secret 5 $1$IC2H$C4aw2Gee5s9Cb.jU8d2pk0
!
!
!
!
interface Multilink1
ip address 168.215.163.94 255.255.255.252
ppp multilink
ppp multilink fragment delay 500
ppp multilink group 1
!
interface FastEthernet0/0
ip address 216.85.198.81 255.255.255.248
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
no ip address
encapsulation ppp
no fair-queue
service-module t1 timeslots 1-24
ppp multilink
ppp multilink group 1
!
interface Serial0/1/0
no ip address
encapsulation ppp
service-module t1 timeslots 1-24
ppp multilink
ppp multilink group 1
!
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 168.215.163.93
!
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
password 7 14391D5A272A253C37
login local
transport input telnet
line vty 5 15
password 7 14391D5A272A253C37
login
!
scheduler allocate 20000 1000
!
end
---------------------------------------------------------
I am also trying to follow the instructions at
to get SDM up and running, but am having issues with some of the commands.
For example, I can't run show webflash:
I get a Invalid input detected at '^' marker. message.
I also cannot add ip http secure-server to the config. I get the same Invalid input detected message.
As you can tell, i'm new to all of this stuff, but a fast learner if someone out there can lead me in the right direction.
Thanks in advance!!