Search results for query: *

Hi rfpui, I've tried that, there is a Tracker modem working ok on the same board -- I've restarted the board, pulled it - there is a tracker modem on the same board which works fine. Don't ask - due to political reasons the company needing access are not allowed to use the tracker. The answer...

Hi, does anyone know how to configure a modem at the remote end ie that it answers and connects to the Md110. How do I clear the AT commands already stored in it. What commands should I put in it and how do I store these commands so that even if the modem is powered down, they will remain...

Hi --- My Problem - I maintain a 15 Lim system BC9. One remote lim (call it X) was removed from the system by an outside company. This was not done properly, PRINT commands did not work. eg EXDDP:dir=all; resulted in wait wait wait COMMAND LOST. Other print commands resulted in "LIM X IS...

Hi, The cable I use to connect to the IPU is labelled TSRG 103 54 1000 Cheers

Hi, I have md110 bc9.GSM 0 and 1 are duplicated. Two GJUG5 cards are strapped for G3 mode.ieGJC 20 - 23 and GJC 24 - 27 .Only one lim is on each GJUG5. If GSM 0 side 0 is active, LIM 17 goes in on GSM 0 side 1,GJC 24 and comes out on GJC 25 towards GSM 0 side 0 GJC 24 (works ok) But!! Lim 16...

Hi I have a little problem -- I have a hunt group set up which is supposed to divert to Octel voice mail on busy or no reply. The group is set up so ------- ghdap:grp=1234; ghdap:grp=1234,serv=1000,sel=100,que=0, The group has 2 members. the group has cdini to voicemail. problem --- On internal...

Hi Soaplover - That did the trick -- Thanks a lot. Cheers

Hi, My switch, Md110 BC9, will only allow an extension to be a member of max 4 hunt groups. Is there a parameter to modify this? Cheers

Hi again -- It worked fine on the FDT table-thanks -- but there is some confusion about DNT1 and DNT2 - the manual for LCR states that you can have PRE = 8 digits on DNT2 and 16 digits on DNT1 (execptions)- I tested it out and it doesn't work! ENT is usefull, you can go back into the system. I...

Hi, I'm setting up Least Cost Routing. The parameter description states that up to 20 digirs can be entered on the PRE setting - I seem only to be allowed 10 -- anyone know a fix. Cheers

Thanks whosrdaddy cheers

Hi, Why not simple abbreviated dialing. First, find out the routing for 88. RODDP:DEST=88; The response would be something like ---- dest=88 rou=60 adc=0605000000000 trc=0 srt=1 then rodde:dest=88; nanse:numse=88,numtyp=ed; nansi:numse=88,numtyp=ac; nansi:numsi=99,numtyp=ed...

Hi, I have a 2 Lim system without Group Switch. The external synchronisation is set to Lim 2. Lim 1 is the i/o Master Lim. 'Alex' states the synchronisation must be taken from the I/O master Lim. Does anyone know what problems this can cause. Cheers

Hi, Thanks -- spot on both times - sorry about the delay in replying. cheers

Hi, I have to end a digital extension but I get the message "Dir has RAC" - any ideas - also , what is FCN - CLT, cheers hughiepal

Hi, Thanks all for the advice (and keep it coming) - I'll study the info' on dynatext. cheers

Hi, The best way to divert a hunt group to voicemail is to program cdini:htgrp#,div=voicemail#; then as each member of the huntgroup goes off duty they should divert there telephone to there own ext number *2*ownnumber# When everyone in the group is off duty (or on busy) the calls will go to...

Hi, does anyone know how to connect and configure an AAU2 card. I believe it is designed to report alarms over an ethernet connection.