Search results for query: *

Hi I have problem in configutil of iMS 5.1 run on solaris 8. When I execute it , says ========================================================== # ./configutil [28/Feb/2003:06:41:43 -0600] mail [26108]: General Error: func=config_readdriver _fileinit...

Hi Here I am looking for DSP cards separately for Voice termination to the PSTN. As far as I know MICA modems can't do this job !!! What is the maximum DSPs can be used in AS5300 ? -su

Hi I have a cisco AS5300 with 8 E1 ports. And there another two free slots are available. Can I user all 8 E1 ports simultaniously for VOIP calls. That means are there 120 dsp modules available to fix them into free slots of AS5300 and operate it as voice gateway for 240 concurrent VOIP calls ...

I want to configure my IMA 5.1 server to receive mails with user@[ip] formatted TO addresses. Now it says "relaying is not allowed" for such mails. Please help me. -suranji

Hi We are in the process of configuring channalised E1 for leased circuits for remote locations. We hired a E1 link from a local telco and connected to our E1 interface in a CISCO 3660 router. As the first stage we did a loop (physical loop)test for the e1 interface. Then E1 contoller came up...

Hi I am new to iPlanet messaging server and want to install iDA for host multiple domains mail servers. First i installed iMS and then ES. Here iMS installed with default domain eg: internal.abc.com. I enabled class of service in ldap server also. But at the end of iDA installation I am not...

Thanks Spinny I am concentrating on the multiplexor but I don't have much knowledge with multiplexor. Can anybody to help me on configuring multiplexor. Any online guide please .. thanks

Hi At the moment I am installing iplanet messaging server 5.0 on sun box. Same time I want to configure out this server for number of domains (eg: abc.com, xyz.com, cnn.zxc.com) as their e-mail server. (I think iplanet can do it with vertual domains concept). But I am still unable to configure...

only the hostname "zoom" is there

Hi croxo Yes you are correct. I can all the interfaces including xxx.xxx.xxx.2 in the serial interface except my own serial interface (xxx.xxx.xxx.1). I can ping xxx.xxx.xxx.1 from other routers connected to the network . Still problem is there. Thanks -suranji

Hi I am using sun netra t1 and I want to set new ip address instead of old one. I used following steps: #ifconfig hme0 down #ifconfig hme0 unplumb #ifconfig hme0 plumb #ifconfig hme0 172.16.31.1 netmask 255.255.255.0 up create entries in /etc/hosts /etc/netmasks /etc/inet/hosts but after...

Hi I checked the router at the other end and its configuration is xxx.xxx.xxx.2/30. It is Intel express router and using ppp wan connection with cisco 3660 router at our end. -thanks suranji

Hi Actually xxx.xxx.xxx.2/30 is the ip address of router at the other end. and s2/0 ip address is xxx.xxx.xxx.1/30. you can see the second post. My biggest problem is "sh ip route " gives two "C" routes to same subnet. It is the problem that i am facing pinging also...

Hi Here is the "sh int s2/0" output ========================================================== Serial2/0 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is xxx.xxx.xxx.1/30 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload...

Hi I am configuring cisco 3660 router with intel express router to make a framerelay pvc. Anybody has this experience pls help me which encapsulation , lmi type that I have to use with. -thanks suranji

HI Andy Thanks for the quick reply. Destination router has default route to the router that i am pinging from. Once i used the extended ping using ethernet address and loopback address also it fails. I can ping any other interface except whi are blocked by my routing table. further help...

Hi I am having a problem to ping serial interface from same router. But I can ping any interface which is connected through same serial interface. routing table is like this: (given below) I feel somthing wrong in routing table itsenf and anybody got similar situation pls help me Thanks...

Hi When i used ultra sun box and hyperterminal in windows also the BREAK key doesn't work to go to OK prompt. There is no command called BREAK in LOM prompt command set. It says no such command. thanks and still problem here. suranji

Hi This sun netra t1 does not have keyboard or console. Then unable to use STOP + A. If i do that through untra sun box it effets to that ultra box itself only.

Hi I am using Sun Netra t1 system connected with CISCO 2511 terminal server. When I am going to install the t1 it doesn't come to the ok prompt. But it gives me LOM prompt. When I put poweron , it booted from hard disk. That hard disk also has a crashed OS and it also not completed it's boot...