Search results for query: *

I want to create a hunt group and put 4 extension (101,102,103,104) and assign the hunt group number for the pickup dial no. I have created the hunt group and added the members. Now my problem is what is the hunt group number. Thank you

#TheCoreWithin, Thank you. all sorted and was spot on. Can I setup a hunt group and set the Pickup Dail No. to the hunt group number?? so I can have multiple phones ring when the phone goes of hook. Thank you Cheers,

Can anyone help me achieve this task. I have a panasonic TDA100 and want to a situation where an extension on a reception desk can automatically call a designated extension number immediately it goes offhook. Thank you

Hello, after a power failure, my 16 port digital station did not come up when the power came back on. when i reboot, the LED stays on RED and then flashes Green and goes back to red. Can anyone help me here. I power on the module before the control unit. Thank you

Hello,I got a 400 16 Digital Module. I also have a ISDN (E1) and 16 analog trunk module. Thank you for the support. How do i set the locale to south Africa.

I have IPO 403 with 1 16 digital module and 16 analog module. i recently purchased another 16 digital module to add to it. I am based in Ghana

Hello can anyone help me with this error? The Hardware Configuration does not match for the locale. Administration will not be vaild. Exiting the apllication thank you

Hello, I recently installed ISDN(PRI) in my Avaya 403 and want to assign individual direct lines for some particular users. I am able to route calls on specific channels to the users but want to know how to assign the same lines for outgoing calls for the same user. thank you for the help

Hello, I have a IPO403 for my small office and currently using 6408D+ on the DS16. Can i change and use 2420. I want to change the Type of Phone we are using

I have taken the steps in implementing SCN using a IPO412 and IPO406 but calls cannot ring at either side. SysMonitor shows the following: 602046mS CMMap: Mapper::AllocateCodec unable to allocate resource 602046mS SCN USER: MakeCallToNetworkedPBX: pass=1 type=5 ipad=192.168.2.237...

i have configured the port forwarding on the access point router linking the two buildings together but the phones cannot ring but you can connect to the voicemail. any help pls

i have the following check on the IP line Enable Faststart Out of band DTMF Allow direct media path Voice Networking

yes the remote users can access the voicemail with *17

they are on the same network but different location. how do i check if the ports are not opened. is this to do with a firewall??

its centralized. a system on the same network. the ip address of the voice mail is 192.168.1.238 and that of the two systems are 192.168.2.236 /237

the system is IP Office 412 and 406 all with release 4.1 (12) and am using a voice mail lite

Hi, can anyone help me on this issue. I followed the implementation points on setting up SCN but after following the steps provided, all calls to the remote office DO NOT ring but then it goes to the voicemail after 4 rings. They do not ring on both sides.

Hello, I will like to know if Panasonic KX-TD500 is a discontinued product.Also does KX-TD500 support IP cards for VOIP??? Thank you

Thanks Mitch672, I don't want to restrict the users entirely from making international calls. I want the users to have access to dial International but only a set of defined numbers of our associates. Thats about 35 numbers in total. Can i set this up in the ARS Tabel??

We currently run Avaya S8500 server and G650 Gateway. Some of the users have access to dial international but we looking for ways to restrict their calls to a set of defined international numbers. That is if the number you dial is not part of the defined list the call will be restricted. Any...