Search results for query: *

outdoor-underground only. do not use indoor-outdoor product. multi-mode well be fine.

Telecomboy You where very close Press 3 for Auto-attendants Press 1 for Auto-Attendant 1 or 2 for AA2 Press 1 for the Day Message (2 at this point to change the Night Message) Press 6 to modify the menu Press *# (star pound) when prompted for a selector code between 1 and 9- This is where most...

Roger that I'll check those things today Thanks for the help

I think your processor is in wrong slot

Telcomboy This is the exactly the way I have been doing it. You could not have explained it any better. I just can't figure out why it's not taking affect. Once I have performed it as you have pointed this out, I'll call in from outside and it has not changed. I installed these VS about 6 months...

Yes I understand that, however would this assigned lines affect, making or changing main greetings-anouncements.

Yes there are two AA the first AA answers line 1-3 And the second answers 4-5, I have tired to change both AA-1 and AA-2 with no luck. Do I have to unassign these lines to make chances?

I have a VS-rel. 5 partner system; I can not change main AA greeting or announcement. I have followed all the procedures in the manual. I have recorded the new message and saved it; I have listened to the new recording and have accepted it. However when calling into this business; the greeting...

MICS (6.0) has 3 analog CL cards, (two in KSU and 1 in trunk mod.). We continually drop cards 2 and 3 Lines 5 through 8. No events recorded, Cards and KSU are new. Solutions have been to reboot. All is well after rebooting. Any suggestions welcomed. Thank you

Yes Fiber would be a great solution. I did give a fiber solution to the client; however there was a down side to this. A fiber solution would create a weak link to the client’s solution. The media converter would require another 110 voltage run to each drop and the converter itself would or...

Thanks for the advice Wires, Oldtimerbob and SyQuest. When writing a thread it hard to cover all the facts and communicate to the members of the group you are asking for help. Such as I failed to mention, the MDF room is 10’ by 15’ has its own isolated ground system, generator powered failure...

Thanks for your input. The electrical contractor has mentioned the building will soon be lightning protected. The IDF box will be mounted to the column by struts. In your option should I scrap the paint off the column, leaving strut metal to metal column contact? Or should I have the electrician...

I'm currently in a new manufacture plant and we are going to install a 6a shielded copper infrastructure. The config is as follows A fiber backbone will run from a sever room MDF to an IDF box mounted on a floor to ceiling column. The outside columns of the building have been grounded and...

Has anyone had any experience with the old 12"x12" interlocking ceiling tiles? I have asked a few techs, but have always come up short. I have struggled with tiles many a time, but have always screwed them up when reinstalling them. Would like to know how to properly disassemble and reassemble...

Thank you all for your suggestions. I have tried all of them. In this case, Dupreet advice was correct. Minuet was trying to load in the cinphony directory. We remove all files in OS2 cinphony directory and reinstalled minuet. Once again thank you for your time

Thank you all for your input. I have tried your suggestions, and unfortunately have not had any success. I e-mailed cintech, and they sent me a autoexec edit line to boot the NAM to.This solution was to rename any file pertaining to any previous installation. Allowing me to complete a new...

I have a problem with the installation of Minuet ACD on a refurbished Rel.4.0 NAM. I have the installation diskette and have called and received from Cintech the key code number, and have followed the manual installation procedure. The floppy drive responses to the installing request, (the drive...

No i have not, but I will try this. All other sets are ring only. Thanks

I must be missing something?? I have a 0x32 with two ASM’s. I would like to assign a DID to one port, so the user can have faxes deliver to their own fax machine. The port is 0506, which has a DN# 4469. I gave 4469 a target line {200} and in LINES (200) I gave it ‘receive digits 0449 which is a...

Great. I thought this would be the way.However my Customer setup the new 800# with the carrier, and they told them that "I the Vendor" would know what to do, useing their DISA system. Not knowing what DISA was I assumed I could see the line and asign it myself. Now that you have...