Search results for query: *

You will need to use NAT.. [americanflag] Go Army! Tek-TIP Member 19,650 CCNP, CCNA, Net+, Sec+ etc etc

has anyone configured a Cisco Unified Border Element (CUBE) to connect sip trunks between a SV8300 and a Avaya CS1000? Any assistance is greatly appreciated thanks in advance! [americanflag] Go Army! Tek-TIP Member 19,650 CCNP, CCNA, Net+, Sec+ etc etc

The channel group was nagging at me as well but I could not remember. [americanflag] Go Army! Tek-TIP Member 19,650

The circuits goof then... Did you verify that your using hdlc or ppp on both routers? Also I'm wondering it could be a clocking issue. example ! network-clock-participate slot 1 network-clock-participate wic 0 network-clock-participate wic 1 network-clock-participate wic 2...

Question 1: You will connect to a swithport and use a WAN ip address given to you by your provider, Given this has a internet connection and not a point to point solution. Question 2:Is this a mpls type service? Some how the two bounded T1's need to interconnect. If so you will obtain ip's to...

Do you have access to the circuit? What errors are on the circuit card (NIU)? Sh interface serial0/0:1 to verify no loops on the circuit. Also verify both ends are setup with HDLC or PPP! They must match. [americanflag] Go Army! Tek-TIP Member 19,650

can you rdp from the inside of the network? [americanflag] Go Army! Tek-TIP Member 19,650

Nice work Whykap! [americanflag] Go Army! Tek-TIP Member 19,650

Kahlaoui1980 Start a new thread!!! [americanflag] Go Army! Tek-TIP Member 19,650

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/7_1_2/ccmfeat/fsccmac.html#wp1144562 [americanflag] Go Army! Tek-TIP Member 19,650

IF both sides are hdlc it will work just fine. Reset the card on the circuit (NIU) just pull it out and replace it.. This will clear a circuit loop. Clear your counters and monitor the interface. [americanflag] Go Army! Tek-TIP Member 19,650

This may help! http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps10326/data_sheet_c78-584412.pdf [americanflag] Go Army! Tek-TIP Member 19,650

SLA. http://www.inacom-sby.net/Shawn/post/2007/11/Cisco-IP-SLA-for-failover.aspx [americanflag] Go Army! Tek-TIP Member 19,650

Have you thought about AutoQos? Check out this web site. http://www.cisco.com/en/US/tech/tk543/tk759/technologies_white_paper09186a00801348bc.shtml [americanflag] Go Army! Tek-TIP Member 19,650

From the manual: Some actions might not be supported in both the input and output direction. CBWFQ can be performed only on packets EXITING the interface. So the answer is you can place them on the input and output. It is determine by what you are trying to accomplish. [americanflag] Go...

Does anyone know how to factory default a CP-500 (524sg) VoIP telephone? The problem is that is will not load, the lights remain on and will not initialize. I know that you can reset if your phone is active but I do not get that far. [americanflag] Go Army! Tek-TIP Member 19,650

http://www.cisco.com/en/US/tech/tk801/tk133/technologies_configuration_example09186a0080093c2e.shtml [americanflag] Go Army! Tek-TIP Member 19,650

So whats connected to the remote router in SRST? Are your phones failing over correctly? [americanflag] Go Army! Tek-TIP Member 19,650

Change the access from 9 to 8. So when someone dials 911 you know it to be true... [americanflag] Go Army! Tek-TIP Member 19,650

Have your local provider run a traffic study on the PRI's. I would find it rather odd that with 12 PRI's, thats 276 lines that you would have any trouble. Do you really have that many lines or is this a fractional pri with 12b channels? [americanflag] Go Army! Tek-TIP Member 19,650