Search results for query: *

Trying to convert an analog station port to voip and then back to analog on the other end of a fiber run. Basically a bridge. There are products out there that seem to do this but I don't know which ones actually work. Years ago I used a Grandstream 501/503 combo, I believe, to accomplish this...

I have a SL2100 with 24 button display phones. Ext. 103 handset does not work but speaker phone does. Swapped with a known good phone from another office and trouble follows. Is there a code that someone could've accidentally dialed to disable the handset?

I have two calling groups 73 and 74. I have extension ringtone pattern 4 assigned to all of the extensions in group 74. I have selector code 4 in Partner messaging set to transfer to 74. When you call in and hit the AA and push 4 the call transfers correctly and right intercom button lights up...

Trying to forward a couple off phones offnet. They work properly if you call or transfer to the forwarded extension but if you dial the extension from the auto attendant it just replays the greeting. Any help is greatly appreciated.

I'm an Avaya tech and I always struggle with these Vodavi systems. What I'm trying to do is very simple but I'm missing something somewhere. I want CO line 2 to ring at station 105 for 5 rings and then leave a message in that extension's mailbox. Then light flex button 24 up indicating a new...

Disregard. Cell was hitting different AP in the mesh than the J179 even though it was laying right next to it. J179 AP had no connection back to LAN. Driving me crazy.

Trying to get a J179 on customer's wifi. IP Office is running 11.0.4 build 3. Phone firmware is 4.0.4.0.10. I'm able to log a cellphone in on the wifi and pull an address that I'm able to ping from the laptop I'm logged into the IP Office with. Laptop is hardwired to customer's network. J179...

Does it work from a landline? If so try going to the "Mouser" under users click source number and add NUSN VCM_RELAX_DTMF_DETECT

Line appearance on the first button makes it grab that trunk when you go off hook. Is this an AT&T BVOIP IP Flex box doing analog hand off?

The original installer set the locale to United Kingdom and the voicemail prompts are in UK English. I changed it to United States but the prompt language is still UK English. The system has been rebooted several times for other reasons if that helps.

Thank you so much for your help. Worked like a charm.

Can't figure out how to turn ringing on for a station. Did feature + hold+#+0+*. Line key 4 gets 01/01:RNG DY 01. I'm stuck there. Tried line key 4 and 10 which gets me to 01/10:STA = 17 WITH the 7 flashing. I got 17 by hitting feature 4 at the station I want to ring which says 84=TEL 17. This...

One thing I did notice is that these were setup originally with the base unit's IP address entered in the VOIP tab. I changed the address to the new one but I've always left that default at 0.0.0.0.

Had three working D100s on 8.1.63 control unit until the customer's IT department upgraded all the switches and created a VLAN for the voice. Changed IP addresses for the SIP dect lines on the control unit and logged into the bases and changed those addresses. Made sure there wasn't a D100.cfg...

Tried Hname and H401 for the extension number of the group. Both do the same on all four phones. Even added the group to the phone in the phone room and it does the same.

IP Office 10.0 Preferred Edition running Voicemail Pro. Customer can listen to a group mailbox message when it's new but when they try to retrieve an old message it asks for a 4 digit agent code. Did I miss a tech bulletin?

Unfortunately I have a 9.1 essential system at a Catholic church that has line appearance buttons on 1416 telephones. They want to pick up the handset and just dial a number instead of pressing the line appearance button first. Can you still put the line appearance buttons as 1 2 3 etc and SA...

Thanks for the help. Will try again in the morning. System was only on the network for the D160s so we built our own little network to bypass the customer's until we can get a permanent fix. Thanks again for the help. Kind of makes me miss the old Transtalk 9030.

Had an IP conflict with the IP office lan 1 address (192.168.1.56) so I changed it to 192.168.1.57. Logged into d100 and changed configuration server address but it changes back to 192.168.1.56 after reboot. Even tried factory initialize but it still changes back after reboot. How is this thing...