Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. SenorAvayaGuy

    abrv-dials, feature buttons not staying in place and is instead moving up a place on the phone.

    @gwebster is that only for 9608's or is this for any 96xx series phone? @sean655 Yes, i found this to be the only temporary solution as well, unfortunately i don't want a screen filled with call appearances or any unnecessary buttons on phone, seeing i'm using a button module for all abrv-dials...
  2. SenorAvayaGuy

    abrv-dials, feature buttons not staying in place and is instead moving up a place on the phone.

    Good afternoon my fellow tek-tip users, i'm encountering a problem where i'm trying to program an "abrv-dial" on a 9608 5th button on a 6.3 CM. Here's the issue i'm encountering, when i place it on the 5th button.. if there is nothing using the 4th button it moves to the 4th button. i'm...
  3. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    As a side note, the G450 used the same IP trunk as the G600 (We just changed the IP to point to the G450).
  4. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    I wanted to say the same, But makes no sense why the old setup (G600) can make calls via the IP trunk to IPO through SIP but G450 Cant. As much as I want to say its provider, I cant fully. And As much I dont want to say its my config... I dont believe it is my config lol. I literally Mirrored...
  5. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Not sure out to export IPO information. not like good Emulation, anyhow. Getting late and Ill probably escalate the situation tomorrow. Ill Keep you posted ! thanks for all your help Joe
  6. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Just full number without dialing 9 as an outside access code
  7. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Yes outbound calls from IP phone registered to IPO work perfectly fine, And IPO routing doesn't need a 9 to dial out (or they must be implementing in a route) I even stripped my 9 via route side (on G450) to see if something weird was happening with what was being outpulsed. No luck.
  8. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Nothing shows on the trace, Not the trunk between the two (IPO and G450). Nor on the SIP trunking either. I would post if there was any thing that showed. Unfortunately there isn't anything showing. Ive hit a dead end, friend lol. I cant think of what it could be thats denying my call and...
  9. SenorAvayaGuy

    Caller id

    Thank you for posting, twas an interesting read lol
  10. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    No, This is a temporary implementation. I was trying to get rid of the current G600 with exact same config (and was working with integration of IPO) and place the G450. Although, this is giving me a headache. I want to point fingers toward IPO but not experienced in IPO to say configuration is...
  11. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Entered in both Private and Public, still denying me.... Any other ideas ?
  12. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Yes just tested with the number placed into Public unknown and its still spitting out the denial event. Banging my head on the table at the moment lol. And I did a trace in IPO and the IPO doesnt see the call even hitting its SIP trunk.
  13. SenorAvayaGuy

    IP trunk from CM to IPO (call denial) denial event 1179: User busy D1=0x41 D2=0x420f11

    Hello users, having issues I hope you can help with. I'm trying to get a call out through a sip trunk from IPO via an IP phone from G450 (IPO is being median for sip trunks as 450 has no SBC controller) Here is my config. Group Number: 2 Group Type: isdn CDR...
  14. SenorAvayaGuy

    Calling remote numbers simultaneously.

    Hello folks, Hopefully you can give me some insight and or helpful tips. Example: I am trying to get whoever call's xxx-xxx-xxxx to route into my PBX, then from the PBX to manipulate the call to hit 2 different numbers simultaneously (Cell Phones) I've tried making 2 IP phones with EC500...
  15. SenorAvayaGuy

    Call into VDN should call to several remote numbers off net

    Telecomadmin12, I'm afraid "completely different problem" isn't correct. Actually both problems are trying to call SEVERAL REMOTE NUMBERS SIMULTANEOUSLY. Using a VDN is just another way at attempting to do the same thing I am trying, I also mentioned using EC500, Is that not the topic of...
  16. SenorAvayaGuy

    Use Ethernet cable instead of T1 cable for PRI, just crimp cable to different pinout?

    This is a good read, https://www.quabbin.com/tech-briefs/why-5e-cable-unsuitable-t1-extensions I've used Cat5e for temporary installs and currently using it for ONE permanent install but it is a short equipment to equipment run and have had no issues so far with slips or misframes. I do...
  17. SenorAvayaGuy

    Call into VDN should call to several remote numbers off net

    I'm actually trying to do this same setup. And have tried a few different routes. Example: I am trying to get whoever call's xxx-xxx-xxxx to route into my PBX, then from the PBX to manipulate the call to hit 2 different numbers simultaneously (Cell Phones) I've tried making 2 IP phones with...
  18. SenorAvayaGuy

    Issue dialing out... Possible DTMF issue ?

    Hello Avaya users, I am having issues dialing out.. I am reading it is a DTMF issue but the resolution was never posted in another forum. So if in this case it is a DTMF issue, what do i do to resolve ? Here is my trace 16:00:50 TRACE STARTED 09/20/2016 CM Release String R016x.03.0.141.0...
  19. SenorAvayaGuy

    IP Office V9 Voicemail to Gmail

    I have Avaya IP Office V9 Just recently switched to Gmail server for Voicemail to email. Can not seem to resolve this issue. It is not embedded. server address:smtp.gmail.com using port 465 use STARTTLS clicked Requires authentication clicked. i also tried ports 587 and 993
  20. SenorAvayaGuy

    LAN access to G600 Definity V9 AVAYA

    Hello fellow users, I have a G600 V9 Definity i am currently working on to try to get remote access to or at least LAN access I have configured the following IP interface Enable Net Eth Pt Type Slot Code Sfx Node Name...

Part and Inventory Search

Back
Top