Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. nzgordini

    7100 Combo Card Going Dead

    Hi Matt Suggest you replace your processor. We have had no explanation from Samsung with regard to our issue, but since replacing our's the problem has disappeared... Gordini
  2. nzgordini

    7100 Combo Card Going Dead

    Hi Russ The issue turned out to be the MP10a processor card. I had also replaced the daughter board cards that you suggested.... Thanks for the response. Gordini
  3. nzgordini

    7100 Combo Card Going Dead

    Hi Guys, I have a 7100 (V4.82) with MP10a in slot 0, Combo2 in slot 1 and a UNI card (with 2 x 4DLM + 1 x 2BRM installed). The combo card slot is going dead every couple of days. It is resolved for about 2-3 days by a power restart. I initially replaced the Combo2 with a Combo3 but still have...
  4. nzgordini

    Adding Additional IP Office Sites To Existing UCM One-X Portal

    Thanks Okkie26 - that's the bit I was missing. I'm restarting now.... Thanks
  5. nzgordini

    Adding Additional IP Office Sites To Existing UCM One-X Portal

    Hi Okkie26 - i'm not sure how to go about that... Thanks
  6. nzgordini

    Adding Additional IP Office Sites To Existing UCM One-X Portal

    Hi Guys, I have two IP Office systems (both 10.0.0.2.0(10)) connected via SCN. I have recently installed a UC Module into one site and have siccessfully integrated this into the local system (both One-X and Voicemail Pro). What additional steps are required to enable One-X and Voicemail Pro...
  7. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Guys Sorted this last night with a complete power down and reseating of the UC Module - Joe gets the star..... What I think happened was that I changed the voicemail password within security settings on the IPO, installed and ignited the UCM and restarted the complete system. But at this stage...
  8. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Hi CarGoSki I'll let you know when I get it going. It does seem as though this may be R10 behaviour as it is well documented in the latest UCM install write up. Gordini
  9. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Nystech - no, completely new UCM V2 install Joe - Not a bad suggestion. I guess it's all getting a bit confused with all the changes I have been doing to get this sorted. I am just off to visit the site shortly - only 72 miles away.... Gordini
  10. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Hi Joe, Yes, a complete power down of the system was one of the first things I tried when I discovered things weren't working.... Gordini
  11. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Hi CarGoSki The address of 169.254.0.2 automatically populates even though the actual address of the UCM is a 192.168.x address - This is quite normal Gordini
  12. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Teletechman - yes IPO is set as VmailPro on UCM Gordini
  13. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Hi Joe Yes, SSA recognises it as Voicemail pro and shows the variant as UCM V2 with the correct software load displayed Gordini
  14. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Joe, if only it were that easy..... Thanks though
  15. nzgordini

    IP Office 500V2 R10 UCM Voicemail Pro No Go

    Hi Guys - I have recently upgraded one of our IPO 500V2 to R10.0.0.2.0(10). This all went well and has been running quite happily for a couple of weeks. I then installed a new UC Module(V2)with exactly the same version of software and it all appeared to go well with no errors during the install...
  16. nzgordini

    IP Office SCN Problems

    Hi Guys, I have an existing full mesh SCN network of 5 systems (mixture of 9 and 8.1) running over MPLS. Two sites have been recently added and appeared to work for about a week. Now we have a problem where the first call to a particular site is successful, but if I hang up and immediately try...
  17. nzgordini

    How To Transfer Configuration From Old Hardware To New

    Hi amriddle01, You are exactly right - what an idiot I am...... I'll see how I get on now that I am connected to the right system - imagine defaulting the next office's system configuration. Cheers
  18. nzgordini

    How To Transfer Configuration From Old Hardware To New

    Hi Guys, See the attached image of the Small Office System I am connected to. I am all too aware of the differences between the IP500V2 and a Small Office System, I am as confused as you on this...... A configuration from another device (Certainly an IP500V2) may well have been loaded onto...
  19. nzgordini

    How To Transfer Configuration From Old Hardware To New

    Hi again... Here is an image of a screen-shot taken from system status when connected to the "new" Avaya Small Office Edition Any ideas?http://files.engineering.com/getfile.aspx?folder=6549dd92-202e-480a-9e39-0352acc456b9&file=Avaya_Small_Office.jpg
  20. nzgordini

    How To Transfer Configuration From Old Hardware To New

    Hi TLPETER Sorry if I confused you, but the hardware is the same. When I connect to the "new" system it says that the system software is 7.0(5) IP500V2 even though I am connected to an Avaya IP Office - Small Office Edition. Thanks

Part and Inventory Search

Back
Top