Search results for query: *

Thanks so mauch. The card should be here soon. I really appreciate it.

I am having a very hard time with this. I have a Dell PE1800 with a dead LSI card. The LSI had a Raid5 container (3 Maxtors) attached. Dell is shipping me a new one out but I need to be deliberate because I cannot loose the data on the RAID5. Do you know any way I can replace the LSI card and...

Hey there. This is a total newb question but I have a 2801 that is running with a 2mft card in it and I wanted to take a WIC from an older 3600 and put it in. I installed the hardware but upon reload I still dont see the interface and there are probably some config steps I need to go through...

Thanks so much. Do you know if you have to use vlan on the sub interface or can I just use secondary IP?

thanks so much.. this helps a great deal!

I was wondering if anyone new a source that could help size / compare routers. I am looking at replacing my aging 3600 point to point routers but selecting a new router since they have been phased out comes with questions. I dont need to bundlle all these services into a router. Im looking for...

We have two subnets on our LAN to segment traffic and we are using a windows box as the LAN subnet router. I would like to offload the routing to a Cisco 3640 that is our WAN router with two Ethernet ports. I’m only using one Ethernet port at this time with an ip address on subnet A , Can I...

thank you very much!... save me.

I am using static routes to manage my WAN right now but I would like to implement RIPv2 . I have used the Router Rip command on each router and entered the IP address of each router for the RIP neighbors but I have no idea how to check to ensure RIP is running properly since my static routes are...

I have a newbie question for you . I have a point to point T-1 down and the CO is telling me its trouble at my A location. I have a LIne Protocol down message and I thought I need to check the clock source on my interface. For the freaking life of me I cannot figure out the command. Clock...

I have a 3600 with DUAL WICS to handle my routing via point to point T-1's to my remote offices. At the hub where the 3600 resides I have two LAN subnets which are routed via a Windows 2003 Server box. I would like to move the routing to the 3600 if it makes sense. I would like to eliminate the...

Is there a way to use ASR without a floppy drive? A flash drive maybe? thanks

Hey there. I have a Microsoft LCS 2005 server running on my network with windows messenger as the client. Its only configured for intranet users and is not setup for outside IM... It has been a very good product and is highly used.

Does BCM 3.6 support caller ID over CAS trunks? thanks so much.

its set to Primary...

We have a BCM 400 3.7 with a Digital Card Module for a t-1 and I have an issue that I have posted previously that I still fight with. 80% of the time everything works perfectly well but then I will get a call from a cell phone from this site saying that there are no lines available. When you...

Thanks for the help. I downloaded the JEEE version 1.4 from this link https://sdlc4a.sun.com/ECom/EComActionServlet/DownloadPage:~:com.sun.sunit.sdlc.content.DownloadPageInfo;jsessionid=DE881E1948A7861FDDA00F0015F0240D;jsessionid=DE881E1948A7861FDDA00F0015F0240D and it is now working. You guys...

We have a BCM 400 running 3.6 and I need to make some important changes yet the System configuration tree is not expanding. When I click the expansion icon on Telephony Services the only thing that shows up is the back/restore tool. I restarted the system hoping it would help to no avail. Has...

all this input id really going to help us. I really appreciate it. Should a regualr electrician be called out to test the grounding system or is this a speciality? thanks again!

thanks so very much. This will help us tremendously