Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. robweston4563

    Voip Lines on BCM50b Version 6.0.2.05.237

    Hi Despite asking both my comms provider and my equipment supplier and others, I cannot get a simple clear answer to this, so maybe someone here can help. We have a BCM50b, version 6, with a DSM 32 module, and a Gatm4 module. We want to add Voip lines to the system, do I need any other...
  2. robweston4563

    Bcm50 GATM4 Module

    I have managed to add the GATM4 module and it is showing up on the system. My next problem is the wiring of lines. This is what i have followed so far, but I do not have a blue or white cable. I have a blue cable with white, and a white cable with blue... but when I use these the line does not...
  3. robweston4563

    Bcm50 GATM4 Module

    Hi I have a new BCM50, I needed to add to it, 4 lines, we were advised to buy a GATM4, which we did and have installed that and it is linked to the bcm. We have wired our 4 lines to this module, but, we have no lines. When I look at telephony resources on the element manager it says: Expansion...
  4. robweston4563

    bcm Ip phones!!

    Thanks Splic. can you ust confirm, is the LAN connected to the switch or the router? Rob
  5. robweston4563

    bcm Ip phones!!

    I have the ip address, I just cannot see how the BCM would connect to the ip phones. The POE switch that is powering the ip units,is not connect in any way to the BCM. Surely the poe switch needs to be connected to the BCm, and i'm not sure it is connected to the right port, or maybe the switch...
  6. robweston4563

    bcm Ip phones!!

    hi Can someone advise me. We have the ip phones connected to a POE switch, which powers the phones fine. When trying to add ip phones, to the system, I am unsure as to how the POE switch connects to the actual BCM. I've tried a few different ports on the front, but cannot get a connection...
  7. robweston4563

    BCM

    Ok... how od i do that and save all the keycodes ?
  8. robweston4563

    BCM

    Can someone advise me how to remove ALL of the following: Target Lines Voip Lines Hunt Groups basically, I need the system to see the lines attached to the GATM module, and lines to ring at the switchboard. At the moment we seem to have a lot of other lines, that are not on the system, but...
  9. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    ok. thanks for all your help :) we are getting somewhere! one last, important question. does every system have the POE- power over ethernet ability, or is that another extra, and how would i find that on the system? Rob
  10. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    can anyone advise me where i can get an upgrade code from Release 1 upwards?
  11. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    I know what i'm doing, i just asked for some advice. I will hit you all up again once ive had this line code sorted out.
  12. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    Soooo frustrated! feel like scrapping the entire idea!
  13. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    hi It's not so much that i'm struggling, it's mainly that i'm getting conflicting information. Can i email you? I'd rather have one source that is correct
  14. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    TELCODOG Under the Resources> Telephony Resources > there is a line that says: Location Module Type Bus State Devices Low High Total Busy internal Trunks 3 Enabling Lines 61 64 4 does the fact that it is ENABLING, mean that there is lines already...
  15. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    So just to be clear the bcm50,even though it has the connections on the front of it for 4 lines, needs a code to make those lines work?
  16. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    Telcodog, can you talk me through the steps, for adding lines, removing lines (all types), adding extn's, and adding and removing ip phones? i have an idea, but i want to get this right, and tbh you have been the most helpful. Thank you again.
  17. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    ok, I thought i could just add the 2 lines, as the BCM50, has ports for wiring 4 lines. (why does it have to be so complicated!!!!)
  18. robweston4563

    BCM50 - Reconfigure URGENT PLS HELP!

    this is the 3rd BCM ive installed, the difference being the others were brand new and easier to install.

Part and Inventory Search

Back
Top