Search results for query: *

AAM Storage and Application 7.1 ACM 8.0 All virtual I've searched 'message log' in the forums and couldn't find an answer. How can I view the life cycle of a single voicemail message? Specific to what I'm looking for... Message left on mailbox xxx a month ago, then forwarded to yyy a week...

AAM Storage and Application 7.1 ACM 8.0 All virtual I've searched 'message log' in the forum and came up with nothing relevant... How can I view the life cycle of a single voicemail message? Thank you

Booted October 2019 with a forklift upgrade of AAM, CM, SM, AES as v/m's on System Manager. Getting with SMTP folks soon. Will post back what's found. Thank you.

Internet Messaging: IMAP/SMTP Status Internet Message status: Running Percent of media space in use (contains queues): 11.0% Number of incoming messages in queue: 0 Number of outgoing messages in queue: 0 Messages in SMTP queues (defer/active/incoming): 228/0/0 Number of SMTP...

AAM 7.1 v/m storage Users complaining about not getting email notifications for many hours after message is left. Below is partial SMTP Log Summary: Internet Messaging SMTP Traffic Postfix log summaries for Apr 17 Grand Totals ------------ messages 1084 received 1106 delivered...

AAM 7.1 storage/application virtual servers Email notification works. However, I need to block emails going off site that are being sent by AAM storage. I only want emails to be sent to @group1 and @group2 and @group3. Everything else should be blocked. Can this be handled by AAM? Thank you

PerContactWaitTime

CM 3.1 SES 5.2 SIP trunks through Cisco CSME to SBC for outbound only. Trouble: Call originating on ACM 3.1 to Vz Wrless user. VzW user lets call ring to v/m and it fails with time out and fast busy. Test call to Vz user who hits red ignore button is successful to v/m. Also, 100% of all...

Get the following after enter: @S8500C> ps -eaf | grep sshd root 24414 1 0 Sep16 ? 00:00:00 /opt/ecs/sbin/hp-sshd -f /etc/ssh/hp-sshd_config dadmin 6607 5503 0 08:35 pts/1 00:00:00 grep sshd Still can not enable via web interface.

Won't be back on site til Monday, will try it then. Thx

Yes, tenet is open. I do not have root access. Hopefully it's not needed.

CM 3.1 8500 stand alone Contains: 01.4.642.1 Reports as: R013x.01.4.642.1 Release String: S8500-013-01.4.642.1 UPDATES: 01.4.642.1-13743 unpacked hot patch 13743 for 01.4.642.1 01.4.642.1-14881 unpacked cold patch 14881 for...

CM 3.1 8720 servers I have seen quite a few posts with no access to " * to program " on 4621SW's. None of the posts detail a solution. I have a number of them running 2.9040, 2.920a, and 2.930a. When the phone boots up the option for * to program has disappeared. It used to be there...

How'd you disable the test so the power alarms would retire?

A retired tech suggested that I wire my new (flat) battery pack parallel to a good (fully charged, in service) battery pack as an attempt to charge the new pack. What do yo think about this idea?

Bumping again with fingers crossed.

Bumped 'cuz I'm still stuck. Any thoughts?

CM 3.1 on s8710's Global MCC Do replacement batteries need to have a minimum pre-charge voltage level for the BIU to charge the new battery assembly? I have installed the new battery assembly because customer needed the large battery cabinet removed to free up floor space (they also have the...

Cust wants it over PRI if at all possible. Do you know what customer options NEED to be enabled for qsig?

Avaya Prologix r12 Shoretel v/m rel ? I'd like to know the minimum customer options necessary to connect Prologix to Shoretel v/m via QSIG over PRI. The potential customer currently has Intuity Audix with IP integration and analog lines. My biggest concern is MWI. I have halfheartedly looked...