Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. RickyPone

    ACD incoming calls

    It's difficult to envision what you are trying to accomplish but it sounds like a hunt group/hunt pilot configuration may work better. You can configure hunt pilot/groups in LD 18, I think. It's been a while.
  2. RickyPone

    No RTP in both ways QSIG

    AvayaHE finished where I was going. You need to build a QSIG dchannel in the Seimens.
  3. RickyPone

    No RTP in both ways QSIG

    So you're using QSIG trunks for a SIP endpoint/interface?
  4. RickyPone

    Sets not forwarding to voice mail

    First trace one of the tns that is hard forwarded to VM. Make sure you see CFW activated. Then change the CLS of the phone to cfxa. Has your VM pilot dn always been a steering code?
  5. RickyPone

    would like to verify FDL on MSDL Card for TTY

    From a good port enter tty x to test the suspect port.
  6. RickyPone

    would like to verify FDL on MSDL Card for TTY

    I would put a laptop on it and send a test to it from another working tty. Just make sure that the baud/parity/bits is set correctly. If it's a qsdi card and depending on your release I think it has to be a D vintage. If it's an msdl pack I suspect your just seeing the dch port trying to...
  7. RickyPone

    would like to verify FDL on MSDL Card for TTY

    Looks like it's downloading the database as a dch. I've never had to download for an SDI device like a teleboss. Have you pulled the card to check all of the switches? What is it an nt8d60?
  8. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    So you're all set? I've seen FLEN work both ways. Sometimes you have to tell the far end how many digits you're sending and other times you can't tell it.
  9. RickyPone

    CS1000 Techs/Administrators Are a Dying Breed

    We use SIP to the PSTN here. 10K DIDs and 350 CCPs. Two trunks inbound one is DR. We've not had any problem with our provider. They do T.38 but to me the real key is the codec. We made sure that only g711 is used. ATT however does suck. As for us being a dying breed, I agree with that but...
  10. RickyPone

    2002p2 issue

    Have you checked layer one? Take the phone to the switchport and test it there first.
  11. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    And try one other thing just to humor me. Change the FLEN to 0.
  12. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    So maybe try this for a work around. Build a phantom tn with the incoming dn. Set a dcfw to a dsc pointed to the asterisk pri. PITA but if it allows you to pass calls who cares right?
  13. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    If it rings through to a Nortel phone then they are sending four. If you don't have to input anything for TEN when building a phone then you aren't using tenant service. I would involve your vendor at this point. Make then escalate to TAC.
  14. RickyPone

    Changing Outgoing Route from Telco to Cisco Tie Line

    I would turn on DCH messaging on the 81 and watch what you are sending across the tie route. Build a test RLI and send one NPA across it. If you guys are still able to dial seven digits then do the same for an RLI to test an nxx with. I would also suggest that the guys who are working on the...
  15. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    Ok kinda forget where we are but can you try this? The dn that you are trying to pass to Asterisk, can you put that on a set on the CS1000? If you can and it terminates on the set you program it on that will confirm what and how many digits they are sending on the LD route. I hate beating...
  16. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    I don't think they are sending 4. These numbers are internal only or are they DID? If the are DID I would go ahead and build an IDC for the whole ten and seven digit number xlating to the DSC. Assign that to route and see if it helps. I never trust ATT.
  17. RickyPone

    Paging Migration-CS1000 to CUCM

    I'm ordering a Valcom 2000A. Thanks everyone.
  18. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    How are the incoming calls arriving? Are they the exact dns as built in CDP or are they sending 7 or 10 digits? If they aren't the dns you have defined you will need an IDC table or change the dsc to match. Sounds like the switch isn't even attempting to signal the DCH.
  19. RickyPone

    Paging Migration-CS1000 to CUCM

    No we do not. But I will today if I can't make this work.
  20. RickyPone

    Two Carriers, CS1K Only Passes One to 2nd PBX

    Have you been administrator for this switch a while? Do you know if you guys use tenant service or have tbar set up? Both could affect trunk to trunk connections. What about TRNX and EXTT in NET_DATA. I've seen those settings cause issues with trunk to trunk connections. Even if the local...

Part and Inventory Search

Back
Top