Ok so tried...
513 and 4410 and 4425
baud: 9600
Data bits: 8
Parity: None
stop bits: 1
Flow Control: tried "Hardware", "None", and "Xon / Xoff"
Manual login: Yes
When Hardware flow control is on it freezes/crashes DSA and ASA
When Hardware flow control = None or Xon / Xoff = blinking curser...
Hi guys,
Here is what i'm trying to do, PC serial port connecting through 9 pin to 25 pin and simple 355A adapter to the Active Terminal port on the back of SPE-A in my Definity G3
What should the Port setting / Delay settings on DSA or ASA
selected direct connect.
Tried emulation
513 and...
Ok well got the Maintenance book for Definity Enterprise comunication server
And Instialization and recovery is just no help
Can't get shadowing to work
Can't get it to refresh
Handshaking is Fine which PDF seems to focus on for some reason.
All bootup tests pass, have a freshly made back up...
Ok Guys I've replaced the MSS board and Disk drive... and All tests are passing now!!!!
So I think I'm ready to boot this SPE-B back up
Could someone help me with steps on that?
sitting at <SPE-B-LOCKED> on the terminal screen
commands are
r - reboot from primary
s - rebbot from secondary...
Ok figured out the stupid test timeout error... Guess My Carrier doesn't want to go through the test all circuit packs (default), as it times out half way through the testing everytime...
All Memory boards Pass all their Tests
Now The Errors come at,
MSS Passed
Disk Harddrive...
Had a week off,
So about to order a (32Mb) TN1650B V4 from ebay and install it...
Would this be a fare assumption since I got the test time exceeded error on this memory board?
Thanks for everything so far!
Port Maintenance On Alt Alarm Svc Ack? Date Date
Name Brd? Name Type State 1 2 Alarmed Resolved
DLY-MTCE n MAJOR 01/02/01:33 00/00/00:00
01B DUP-CHL n MAJOR...
TGIF Guys!
I physically locked both SPE-a and SPE-b over to the A side which then lit an LED and actually change status to locked SPE-A in <status SPE>
I found out I needed to put terminal in the standby port in back of cabnet to see what SPE-B was up to. After removing disk drive and swapping...
Hey PBXTech and AvayaTier3,
In regards to the Power down of SPE-B
Do you mean just Busyout SPE-B? Or actually pull the power plugs for the whole 01B Carrier with SPE-B in it?
Or just pull out the Card in slot Dupn Interface?
Ok tried ejecting the MO disk from the troubled 01B Carrier
with the standby SPE-B... Pushed it back in and got a green flicker nothing major. ran the Command list config software long and got error:
Standby SPE has inadequate health to proceed, for information use 'status spe'
Status SPE...
Searching this great site I found some commands to run...
Definity Flavor is
System: G3rV11 Software Version: R011r.03.2.536.1
Status Spe
PROCESSOR COMPLEX
Duplicated? yes
SPE Selected: spe a locked active
Standby Busied...
Sorry I inherited this Definity setup, could an external Tape backup server be handling the save translations? and I would simply never use this command?
Total Noob with Definity.
Should have asked what commands should I use to start troubleshooting... What TN Card is the Flash card in?
What is the SPE? maybe a quick overview on the Definity duplication process might help me.
What I'm looking at is a Definity 10 Cabnet monster...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.