Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. AKskier

    Appear But No Ring to Hunt group member

    The sets are 9508s. thanks to all for the suggestions, I'll give them a shot.
  2. AKskier

    Appear But No Ring to Hunt group member

    I've got an IP500 version 9.1. The situation is, incoming calls go to a group of sets in the front office of a school and they want to be able to answer incoming hunt group calls on all sets but they only want one set to ring. Sort of like having APPEAR and RING or just APPEAR options on a...
  3. AKskier

    MICS 6.1 TRUNK FAILURE

    Thanks guys, I had just figured that out. I remembered where there was another system in town with the same type of PBX trunks from our switch, so I went and checked it out. E&M and winkstart on the lines. I am now able to send/receive calls. Now I just have to figure out what the customer...
  4. AKskier

    MICS 6.1 TRUNK FAILURE

    I've tried spare cards. I tried the enable/disable of the DTI card a few times. I also made line appearances on the a set of a couple different lines and the same result line in use. Kinda at a loss.
  5. AKskier

    MICS 6.1 TRUNK FAILURE

    This is what I am sending from the CO. 24 2way PBX trunks. TYP LTG NUM 16 APPL PBX TGTP 2WAY TGNM xxxx INC 2 WAY SITE BASE TGDP DIOD RMB YES NTNU YES STPL WINK DT YES RCVR DGT FDTM 8 SEC PDTO 8 SEC CNTL ETHR TRNL STN...
  6. AKskier

    MICS 6.1 TRUNK FAILURE

    Curlycord, In NW Alaska I am what could be referred to as a ditch to the switch and everything in between tech. I have some experience with Norstar, mostly just CICs with a couple analog lines though. The way I have this set up is: Trunks 1-24 - ports 201-224 assigned to Line Pool A Pool A has...
  7. AKskier

    MICS 6.1 TRUNK FAILURE

    It's not a PRI, it's just a t-1, digital trunks with DID's routed over it. Target lines to ring the individual extensions.
  8. AKskier

    MICS 6.1 TRUNK FAILURE

    Hi all, I've got a customer with a MICS 6.1 that has bombed after a recent power outage. The system has 2 t-1 cards one from the LEC and then one for some FX trunks to another system, I assume. Nobody onsite could tell me. There are also 2 fiber expansion cards and several station modules...
  9. AKskier

    5224 MAILBOX BUTTON

    As always, thanks for the input. cheers!!
  10. AKskier

    5224 MAILBOX BUTTON

    Thanks supernova..i figured it out the hard way. so if i want to set up for record-a-call i need to use two VM ports, which should i use..16-17?
  11. AKskier

    5224 MAILBOX BUTTON

    I figured it out. I had put VM ports 19/20 into a hunt group friday afternoon to see if they would be able to record-a-call and that caused me grief on monday. go figure!!!
  12. AKskier

    5224 MAILBOX BUTTON

    Greetings all, I've got a 3300 that i recently upgraded to 4.2 and added an additional 3300 resilient controller. I tested the failover last weekend and that went well and i returned service to the primary controller. This morning I had a trouble call from the customer that the voice mail...
  13. AKskier

    3300 PAGE ALL SETS

    It is a relatively small site and it seems to work fine. They were happy. Thanks for the help
  14. AKskier

    3300 PAGE ALL SETS

    I tried here on the 3300 in our office and it worked without the comma. you are unable to enter a comma in the directory number field. I set it up to test for the customer but haven't heard back from them yet. If it doesn't work maybe i will have to remove some sets from the group. thanks for...
  15. AKskier

    3300 PAGE ALL SETS

    Hello I've got a 3300 9.0 installed in a small hospital, and the customer is asking if I can set up a button that with one touch will allow them to page all sets. Right now i have a voice call button on the sets and after pressing that they have to hit 00 to generate the page. Apparently...
  16. AKskier

    telephone directory synchronization

    well, that's a bummer.
  17. AKskier

    telephone directory synchronization

    I am changing out our office 3300 with release 8 software to a new 3300 MCD4.0. I transferred the licensing from the old one to the new one and I am trying to restore the database from the old controller to the new one. It appeared to be working but after a couple of minutes I got an error...
  18. AKskier

    Loud Bell in remote factory via fibre???????

    I've used the grandstream sip ATA's for loud bells and these seem to work pretty good.
  19. AKskier

    PRAIRIEFYRE CALL ACCOUNTING

    Thanks That's what I was afraid of.
  20. AKskier

    PRAIRIEFYRE CALL ACCOUNTING

    Hi All I've got a 3300MXe 9.0.2 and I've just installed PrairieFyre for call accounting. I have it sycned with the controller and I can generate reports and whatnot. My problem is that the customer has account codes they have to enter that they have been given by their LD provider in order to...

Part and Inventory Search

Back
Top