Search results for query: *

Try comparing your NET_Data blocks. They can be found under LD 21. PRT net_data. Also are you using Session Manager to route calls between the sites?

If the 3903 has a X on the screen, then go into LD 32 and do FLDF using the TN. This happens on my site when the user unpluggs the phone in the middle of a firmware upgrade

go into LD 37 and stat you tty. The UCM and VT uses virtual TTY for connections. You can add more virtual tty in LD 17.

Guycable has the answer here. I didn't have a 1150 to test with so I was using an 1140. The Bluetooth headset works fine picking up both lines on an 1140.

Ok that helps. I'll get my Blue Tooth set up and get back to you

Is the headset plugged into the headset port in the back of the phone? If you can not pick up the call with the headset button that could be the problem. You should be able to answer the phone by pressing the headset button. You may need a lifter kit if you are trying to answert the call be...

I have an 1140 with headset, IRA, LPK 2. When I ring line 1 and press the headset key, the headset picks up. Does your call on line 1 go to Handsfree?

try going into the phone by pressing the Services key once.At the Telephone options press select. arrow to on hook default path,press select.arrow to headset enabled, press select. then press the quit button. When wearing the headset, dial tone or call will come through the headset not jump to...

Angelo, Since TAGR is set to NO in the ESN data block you are using NCOS to restrict phones. To make the non-DID phone access the Outgoing Analog trunks, make the NCOS of the phone match the FRL of the entry that the Outgoing Analog Trunks are in. example: RLI xx entr 0 route xx (outgoing...

DO NOT change your TGAR to yes in the ESN block. This will cause distrubtion in your calling based on what youhave posted before. Post the RLB and the TN print out of a DID and NON DID set.

Angelo, go into load 86 and prt the ESN block. req prt cust 0 feat ESN At the end of the block see if TGAR say yes or no. If it say no then your system is not checking for TGAR. It is using NCOS for routing. i say this because the info posted shows TGAR of set and TARG of set to match.Post a...

I ran across this problem when doing upgrades to 6.0.The first time a call is placed across the DB you get no way speech path. To get around this I disabled the 32 port DB, made a call across the 96 port DB. Keeping the call up and wait about 30 seconds the call will establish. It then will...

The Call type is important for the SL100, check to see if the SL100 see it as public or private. The CTYP can be changed with a DMI table in LD 86.

ripo, You are correct with the answers for question 1. LHK will hunt a call to key 1 when key 0 is busy. In the CLS of the phone add FNA and HTA as well as the pilot number for VM in FDN and HUNT For question 2 ,add a D after the DN on key 1. I pasted the information from the NTPs. key xx SCR...

If you are using the TSI fiber remote interfaces, then you may have one go bad. You have lost connection to the remote side

I believe this is left over from your MM. You have removed the AML link, now you need to remove the VAS ID of 9. Go to LD 22 and print the VAS. ld 22 req prt type vas What should print out is the VAS 9 for the MM and VAS 16 for the Call Pilot. Go into LD 17 use the gateopener VAS and remove...

GH is on the right track in LD 32 type FWVU 12 0 1 2 (that's the TN of her phone) if the phone is firmware version 87 then type in FDLU 12 0 1 2 Her phone will be off line while the firmware is downloading so you may want to call her first I have seen this problem on M3904 with rel 6.0 and...

LD 22 req:slt

to reset the 6120 to factory default. Power off the phone. Press and hold the green and yellow buttons. When the MAC address appears, release the yellow button. Password will appear release the green button. The default password is 123456. Press the arrow key in the middle of the phone. The...

Barry- Have a simple question. When you added the T-1, did you also add a Clock Controller daughter board to it?