Search results for query: *

I am trying to program a unique ring between two lines on my ACS R6.0. If you program line number two with unique #2 will the line ring uniquily on all phones? Is this procedure is used to differentiate the ring tone between two incoming lines.

I have been reading about Guest Mail boxes in a Partner Mail VS R4.1. Is it true you can assign a guest mail box using the extensions in the slot populated with the Partner Mail VS module? For example I have a Partner II. The voice Mail module resides in Slot 4 of the expansion carrier. Those...

Has anyone had experience using a Viking Paging Horn speaker 25AE. I had a Harris cone speaker go bad and I need to replace it. I cannot find a Harris cone speaker anywhere. Is the 25AE a good replacement for the Harris cone speaker?

I have seen this done before but I can't remember how to program it. Instead of hanging up the receiver after using the loudspeaker paging how does one create a release key next to the Loudspeaker Button.

The AT&T 984 and two AT&T 965's would work good. They are four line telephones. The 984 has built in digital answering system. Message waiting light plus mailboxes. Then you would not have to pay telco for voice mail.

Partner II R4.0 with Voice Mail VS R4.0. When retrieving voice mail messages user hears messages that are garbled. This is an intermitant trouble. Processor or Voice Mail module?

Can someone please tell me the temperature operating range for the Partner ACS R6.0. The Partner R4.1 range is 32 to 104 degrees F. I the ACS R6.0 the same?

The client does not want callers going to a mail box. They want all callers to be connected to a live voice. If I took the same extensions, removed them from the Hunt Group and put them in a Calling Group, do you think I would have the same results.

I created a Hunt Group. (772)I put four extensions into the hunt group. Ext, 10, 29, 36 and 37. I have a selector code (7) pointed at the Hunt group (772). When all the above extensions are busy with callers, the fifth caller to the Hunt Group gets ext 10 voice mail box message. I installed a VM...

A nice addition to a nice system. An inexpensive way to add a second quasi AA.

Can I use a VMS Cover Button (Feature 15) to turn off an extension's voice mail box? I'm not sure exactly how it works. When the button is in the 'on' position what happens?

You can use Direct Extension Dial for the second business, you have 20 seconds to give a short message, callers would hear the short 20 message and then be prompted to dial extension xx for Acme widgets, etc.

Thank you for the info. Unbeliveable that Lucent would create a system that did not contain ringing to an extension upon transfer. Must be they were trying to sell Music on Hold.

I have installed a Partner II R4.0/4.1 When calling into the system from the outside and being transferred to an extension callers do no hear an audible ring. I tried procedure #119. It would not allow me to get into this procedure. Should procedure #602 be set for active or not active. Their...

It is a Partner II R4.0

I went right to Extension 21, dialed Feature 00, push button 'B' (Line #2) is says DXD button. I went back to Ext 10 and it will not allow me to remove it. Any ideas to remove it? Could it be a hard drive glitch?

Partner Processor R4.1 Partner Voice Mail VS R4.0 The system is an existing Bilingual Mode Voice Mail System. I set it up with a Selector Code pointed at an extension. Spanish speaking callers call into the system, they are instructed to dial *1 for Spanish. If they dial 6 they are routed to an...

I haven't tried moving it to another button. Only trying to remove the button labled DXD. I agree that only Ext. 10 can have a DXD button. I'm seeing the DXD button by getting into Ext. 21 from Ext. 10, Feature 00, System Program, System Program, Central Tel Program, 21. I discovered the...

I cannot remove DXD from a button on Extension 21. It is frozen to where Line #2 appears on all other telephones. I use procedure #113 - 2 to unassign. I can make the button go blank but when I assign Line #2 to that button DXD pops up again. None of the lines are assigned in procedure #205. Any...

Does anyone know where to get a programming overlay for a 34 button MLS set?