Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. rbelleroseanalog

    Noise on paging system (CS1000, UXT

    thread798-1698595 So my previous post indicated that our vendor hears noise on the overhead speakers off the paging amplifiers and the electrician with very little voice experience was trying to eliminate the noise with shunts and grounding the shielded cable that was being used. Fiber was...
  2. rbelleroseanalog

    Modem on VG224 Issue

    ! voice service pots fax rate disable ! voice service voip fax protocol pass-through g711ulaw modem passthrough nse codec g711ulaw ! I stole this answer from another post you might want to check the config for these lines especially the modem one.
  3. rbelleroseanalog

    add on module for a 3904

    I think the first key will be key 32 and you need to add the add on module feature or set it to 1 for AOM i think, then add the feature to the key bottom left key is 32 going up the left then up the right side. Try it...
  4. rbelleroseanalog

    Command LIne auto update via SNMP

    Does anyone use the snmp feature that updates the CS1000 Gui interface if someone makes a change using command line? If so can you share the procedure or where the installation document lives and if you are using how do you like it? Basically if you have techs who don't use the GUI and a help...
  5. rbelleroseanalog

    You Know Your A Nortel(Avaya) Tech If

    When you referred to the option 11c as a COW which stands for Corruption On Wall.
  6. rbelleroseanalog

    Overhead paging Noise

    Maybe someone can help here. Existing paging system uses UTC, loop start. Local electrician ran 900 feet of direct 24 gage sheilded line. Still picking up 60 cycle hum and 1.3mghz signal on the run with nothing attached at either end. Basically a big atenna, so the powers that be want to run a...
  7. rbelleroseanalog

    7.5 - Cannot get into Element Manager from System Manager

    Our vendor in the past has restarted the Jboss application and that cleared up the issue. Also make sure the redundant systems are sync-ed up.
  8. rbelleroseanalog

    Audio Codes

    Anyone using audio codes where the E1 is using Euro instead of ISGF on the Dchannel setup. The pbx does not have pgk 305 so IGSF is not available and we want to use and existing Audio Codes box for SIP access from the opt11c.
  9. rbelleroseanalog

    "No route to destination" Nortel 5.5 to Cisco rel 7.0 via NRS

    We need to see the 6 its the way they setup our numbering plan even though the 6 is the access code for Cisco and UM intergration. The cluster is not ping-able from the pbx but it is from the element manager / sig server. The sip test works fine from the NRS also goes to the correct IP etc. I...
  10. rbelleroseanalog

    "No route to destination" Nortel 5.5 to Cisco rel 7.0 via NRS

    I have a sip route setup to with a Cisco call manager. The soft phone I am using can ping the cluster IP however the pbx it is registered to cannot ping the cluster. No route found is the message when making the call to the cluster from the pbx. ROGRESS: ORIG ADDR IS NOT ISDN CALLING #:61057051...
  11. rbelleroseanalog

    I2050 and i2004 lost dialing capabilities

    Initially the complaint was i2050 phones not able to dial anywhere via that pbx. I put an IP phone on my desk localy registered against that pbx for testing and the same condition existed. The issue ended being the zone for IP phones being diabled, when the zone was being checked and showed it...
  12. rbelleroseanalog

    I2050 and i2004 lost dialing capabilities

    We have a site where the softphones register ok get dialtone but once they complete the dialed number whether on-net or off-net the call fails and re-order tone is presented. You can reach the site fine via ITG and tdm phones dial out fine over itg from that site. The softphones are register...
  13. rbelleroseanalog

    Bug4304

    Anyone ever seen this bug before, dchannel error? Carrier? any ideas? Looks like the it happens intermittently and I see no counter error on the pri. Thanks BUG4304 % BUG4304 + 1067E160 106A6F4A 106A6DF8 104EFD1A 104ECAF6 % BUG4304 + 104EC598 106B8C0A 106B89DE 106B77AE 10CEC808 % BUG4304...
  14. rbelleroseanalog

    CS1000m 4.5 via E1 Qsig to Audiocodes

    Anyone using an Audiocodes box on an E1 qsig pipe, if so do you have the setup for the audiocodes side for trunk configuration? And are the channels 1-31 or 1-30? Thanks.
  15. rbelleroseanalog

    Hacking

    I actually found the COS and dis abled the transfer function. FYI the number is 8125402800 which is not anything meaningful, does not match any country code with a real city code. But if you see this you will know they are trying to bounce from system to system. They are now dropping off as they...
  16. rbelleroseanalog

    Hacking

    I have an active hacking situation, how do I drop current line? Also does anyone have guide lines for securring the BCM. Currently they are getting into the mail system and getting out. I have added the numbers they are dialing in the restriction table but they have multiple numbers they are...
  17. rbelleroseanalog

    CallPilot login

    Problem found using cptrace, the pgp email proxy was causing the problem. Thanks everyone.
  18. rbelleroseanalog

    CallPilot login

    The 'Login' authentication method is disabled. Please contact your administrator. Anyone ever come across this error above login into the callpilot rel 4.0 using desktop messaging?
  19. rbelleroseanalog

    BCM error

    Hey Ace what I mean is rather than pulling the plug physically out of the wall and counting to 10 is not always the solution despite what you may think. Minimal impact to end-users is the preferred course of action in my world. FYI I found that patches are missing and should keep this from...

Part and Inventory Search

Back
Top