Search results for query: *

Hello Gurus... I am here again.. My newly build PC is getting stuck at the message "Verifying DMI Pool Data" after an attempt to load Linux The linux installation crashed after formatting the disk and before copying the image files to disk. My system board is GA-MA770-DS3 Any idea what is...

Put the 8600GT card in. It worked..... Thanks a lot for your help.

Thanks for your advise. This is a home built PC..I have tried both DVI and VGA. Didn't help Tried resetting the CMOS.. - No difference. Now I have sent this card for replacement. I am getting temporary card from one of my friend by this Friday.That is 8600GT. Hope that is going to work.

Hi Gurus, I have built a new PC with the motherboard GA-MA770-DS3. I am using Inno 3D 9400GT graphics card. The problem is I am not getting the display. It gives one long beep and 2 short beep. As per the manual, it is a problem with graphics card or the monitor. Monitor is fine. Do I need to...

Yes. of course.. AIX 5.3 can be installed on H80. But it is a bulky system and is not good for keeping it at home and practising AIX. 6C1 is much better in this case.

I am not sure where it will cheap.. Ebay is a good place. However buying second hand server is bit risky since parts are very costly. I would suggest to go for 7028-6C1 out of the above two. Nowadays practicing AIX is not just the administration of Operarting system. You need to do LPARs...

Both the servers 7028-6C1 and 7017-S85 can be used for loading aix 5.3

Assign all the resources to one LPAR Boot the LPAR from diagnostics CD Go to Task Selection > Format and Certify Select all the disks and format

I dont think you need a paging01 here. Two paging spaces should be fine hd6 with 12.5 GB ( LV Mirrored b/w hdisk0 and hdisk1) paging00 with 12.5 GB (LV Mirroed b/w hdisk2 and hdisk3) An additional paging space on the same disk do not give any performance improvement

FTP stands file transfer protocol . By native design it does not support directory tranfer. You can use third party tools like Filezilla for Cute FTP.. As Columb mentioned FTP is not advisable since it not secure. Using scp you transfer directories

I think hd6 is mirrored between hdisk0 and hdisk1. Can you get the output of the following ? lslv -l hd6 lslv -l paging00 lslv -l paging01

Paging space of 25GB doesn't look good. What is amount of memory installed? What is your paging space requirement for application? Paging space is not a replacement for memory.. However you can do this with the following commands Extend your paging space hd6 by X where X= (8704-384)/(PP size...

Most of these errors are due to dns resolution. Can you check whether the reverse lookup is working? It is better to add an entry in the /etc/hosts of both servers.

Yes. Are you getting a similar output when you give the command smtctl #smtctl This system is SMT capable. SMT is currently enabled.

By any chance you are using AIX 5.2 on the second server which do not support SMT even if you have a Power 5 processor

I think in the first system with 4 Physical processor is a Power5 system and you have SMT ( Simultaneous multi threading ON).. If you not you have defined the number of virtual processor as 8. In the second server, one of the following 1. It is not a Power5 system 2. SMT is not ON or 3. The...

I think you were using 18 GB disk before with a MAX number PPs as 1016 per PV Now you are trying to add a 36 GB disk which requires 1152 PPs since you are using 32MB as the PP size. To increase the MAX PPs to 2032 you need to use the factor 2 chvg -t 2 backup2vg However you get into another...

Have you tried using mkuser command?