Hi pal, My MC32s is programmed as VGW channels, this error occurs when i created a zone1 and zone 2, i put all SIP trunks in zone2 and tried to put Mc32s in zone1, previoulsy mc32s was in zone 0. I then deleted zone -1 and EDD then restarted PBX and got every thing OK.
Any advise??
Hi i am getting ERR008 4 0 5 0 8 1 5 4 randomly and call between cabinets got silent or no speech path. Then TN`s are random but this error is between cabinet to cabinet only, with cabinet ext to ext call is OK, it is cs1000e rls 5. Can somebody point a right direction to resolve this?
Can somebody briefly explain what rule should i follow to set VPIM??? i mean how to calculate/describe rule for setting VPIM prefix in Callpilot 4 or 5.??
does it related to DID range i mean lets say i have DID number ranging 5206000 to 5207900 and my extension are bulit from 6300 to 7200...
So what you guys advise about the configuration given below
MGC/DB`s =Zone1
All IP sets=Zone2
SIP trunk=Zone3
MC32s=Zone4
On Site 2
MGC/DB`s =Zone4
All IP sets=Zone5
SIP trunk=Zone6
no MC32s card at other site.
is that correct?? if i set IP phone zone 2 ans SIP with Zone3 then does IP...
Hi all, it is CS100E rls 5. its been in installtion phase, i programmed all analog/DLC/IP softphone ext with everything accept Zone, i didnt created any ZOne and all MGC/DB`s are programmed with no zone entered. Today i created Zone 2 and communications between got stop , call within cabinets...
Hi all. Can somebody point me how to upgrade loadware of MGC. I downloaded 6 loadware files of MGC from ESPL site and tried to load these files through Element manager
Software--->Upload file but it pop an error that the file syntax should not conatin /, \, % etc and file extension must be...
Hi Thanks all for helping, I am going to do as tnphoneman advising, I was going into depth in this posty just because i wants to understand more from this forum, though i am also reading NTP`s but it is more easier to learn practical experience from this forum. Thanks and regards
I am planning to use these cards as under please advise if it is OK.(This PBX have almost all TDM stations and so mostly TDM resources will be use,another thing i didnt mentioned that i got one 96 and four 32 port DSP d/brd with this)
(1) First cabinet= MGC with 96 DSP D/brd+6 PRI cards+Mgate...
allenmac , these are 11c Cabinet having 10 slot in each, it is also of SA config ,no HA. Cant i have 40 slots in 4 cabinets??? If yes then please advise how can i distribute cards and DSP D/brds in between these cabinets.
Hi Pal, look i got Five 32 port dsp daughter board with 4 MGC card and need yours assistance how to distribute thes all PRI/Analog/XUT/6 PRI in these 4 cabinets and distribution of Five 32 port dsp D/board. I am really stuck on its engineering and i need to avoid any blockage situation.
Need...
The situation is that i got Five 32 port DSP D/board with 4 MGC card and I have 4 cabinet system with 195 analog, 24 digital extension,4 XUT cards and 6 PRI`s, Now can somebody advise how can i distribute these all cards with 4MGC and Five 32 port DSP D/Boards.
Regards
Hi all, i need some info regarding MGC DSP usage of CS1000E. I mean with different call scenario. Can somebody answer these separately whether DSP is use or not in these call setup.
(1) Analog to analog ext call within cabinet or cabinet to
cabinet-->DSP is use or not?
(2) Incoming DID...
Is there any product bulletin or document or some info about compatibility matrix of release 5 with SSC card and daughter board vintage and flash boot room version for release 5. this info is needed for CS1000M cabinet release 5.
I was seraching on Nortel site and found some matrix but not...
Hi all, i have installed a Callpilot 600r release 5 with CS1000M rls 5 with 40 Fax messaging license also. Now to setup Fax messaging(to receive Fax msgs into outlook) i need a CLAN IP which customer dont wants, i mean they dont want some other device on there LAN for some security purposes...
Hi all, Thanks for helping... I tried setting DEVICE to rlogin and Emulation to VT220 but still getting same message or rejection. I connected MY PC directly to PBX and i can ping.There is no firewall installed.
Regards
Hi it is 11c rls 24.24. IP`s and sub net mask are set to default in PBX, One PTY was also created in PBX and i can ping PBX from my computer. I tried ZOC and hyper terminal (TCP/IP) to connect but it pops error (i think error is connection refuse, in ZOC port was set 23 and i also tried 25,22...
I didnt test 3PE and CNI`s, Can i use different CNI eng. code with cores. i mean i have a backup CNI card but its eng code is different from CNI presently in the system can i use that CNI card?? Also which core CNI or 3PE do i suspect?
regards
When i stat (system is on core0) CPU it shows CP-0 in split mode and CP-1 in disabled and when i stat (system on core-1, after unplugging/disabling core0 and sysload system works on core-1) CPU it shows CP-1 split and CP-0 disabled.
The problem is that SYNC/JOIN/SCPU/SPLIT dont work neither...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.