Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: AC427
  • Order by date
  1. AC427

    High response times during the night when there is very low utilization

    Hi, I have a 2901 router which is showing some odd behaviour. During the evening/night/weekends when there is no load on the CPU or WAN link the response times to the router over the network becomes quite high, anything between 200 - 600ms. The normal response time during the day when it is...
  2. AC427

    LFAS error on PRI2

    Hi, I have a PRI circuit between 2 Option11s and am getting the following error at one end PRI2 LOOP 1 - ENBL REF CLK: ENBL TRACKING SERVICE RESTORE: YES ALARM STATUS: OOS LOCAL ALARM : LFAS CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD * CH 03 - DSBL TIE VOD *...
  3. AC427

    i need busy tone when phone is busy!

    This is the trunk that i dont get busy tone from YPE RDB CUST 00 DMOD ROUT 110 DES EURO ISDN TKTP DID NPID_TBL_NUM 0 SAT NO RCLS EXT DTRK YES BRIP NO DGTP PRI2 ISDN YES MODE PRA IFC EURO CNTY UK SBN NO PNI 00000 NCNA NO NCRD NO ISAR...
  4. AC427

    i need busy tone when phone is busy!

    There is no loops etc as the only place it has been forwarded to is itself or no forwarding at all. After further testing i have found it gives busy tone on internal calls and from an IP incomming call, so it looks like it might be a trunk setting.
  5. AC427

    i need busy tone when phone is busy!

    someone has advised me it might be a setting called Treatment somewhere in ld 15 CDB. Any ideas if this is an option and if so where?
  6. AC427

    i need busy tone when phone is busy!

    Hi, Thanks for the advise, but neither worked. I was initially thinking it was just with this set, but its the same on others, so im now thinking its a system wide issue. is the busy tone set in the trunk anywhere perhaps?
  7. AC427

    i need busy tone when phone is busy!

    Hi, Im sure this is a simple issue and its staring me in the face. I need a 3902 to give busy tone when its busy. At the moment all it gives is the continuous dead tone when the phone is in use. I have tried the phone with no forwarding of any sort, just FDN set to forward to itself and all...
  8. AC427

    Restricting Call transfer

    Hi, Both Meridians have the following in NET DITI YES TRNX YES EXTT YES FTOP FRES and neither have XFA in the CLS as they are digital exts, my understanding is that is a 500 set CLS.
  9. AC427

    International dialling not working

    i finally got to the bottom of it. I removed SPN 00 and allowed SPN 0 to dial 17 digits and it now works. Thanks for the advise though.
  10. AC427

    International dialling not working

    Ive already tried UNR and that didnt work. The thing that concerns me is that the Meridian is letting him dial out but only seems to be sending the 00 part of the number.
  11. AC427

    International dialling not working

    This is the only phone on the Meridian that has ever been allowed to make international calls so i cant compare it to a working TN unfortunatly. The international number being dialled is the correct number as it works from other places. The number being called is 00 353 xxx xxx, so its not...
  12. AC427

    International dialling not working

    Hi, I have a single 3903 set up to allow international dialling but it has stopped working. The NCOS allows international dialling and i have tested this by changing the NCOS on the set to a different class. When it has a international barred NCOS it doesnt allow the call, but with the allow...
  13. AC427

    Restricting Call transfer

    bump. thanks for the advise so far, but none has worked. Any other suggestions?
  14. AC427

    Restricting Call transfer

    Thanks for that. Ive looked at both systems and they both have the following set CDB Net Data TRNX-YES EXTT-YES A set from the system that can transfer has FTTC in the CLS and a set from the system that cant has FTTU. So neither of these settings seem to be the one that is stopping the...
  15. AC427

    Restricting Call transfer

    Hi, I have a customer with 2 Meridian Opt 11. running 25.15. On both systems they can call mobiles and national numbers, but one cant transfer calls to mobiles and national calls. They want this implemented on the other, but i have no idea how thats set up. My understanding was that when a...
  16. AC427

    Backup over ISDN dial up on BCM400 3.6

    Hi, I have been asked to perform a remote backup of a BCM400 3.6 and the only access is via ISDN dial up. I can dial into the BCM and access the BRU utility and set up a backup the same as i would do a remote backup over a network, but it is not working. It cant access the network. The BCM...
  17. AC427

    Unanswered transferred calls are not being released.

    Here is a print out for the RDR_DATA, but i cant see anything that relates to transfered calls. REQ: prt TYPE: rdr TYPE RDR_DATA CUST 0 TYPE RDR_DATA CUST 00 OPT CFO CFRA DSTD PVCA CWRD FNAD FDN FNAT FDN FNAL FDN CFTA NO CCFWDN CFN0 6 CFN1 6 CFN2 8 DFN0 6 DFN1 6 DFN2 8 DNDH NO...
  18. AC427

    Unanswered transferred calls are not being released.

    Hi, Im running an Option 11 R25 Issue 11 and am having a problem with call transfers. The user answers a call and transfers it to another phone, if that phone isnt answered and they take the call back and take a message 2 things happen. Firstly, the phone they tried to transfer it to keeps...
  19. AC427

    Option 11 Restarting

    More info. Apparently this problem happened a few months back and after the system was rebuilt it with a new SSC card it was still doing it. After replacing the PSU it stopped, but has now started again. The users have also now complained they are getting crossed lines from within the...
  20. AC427

    Option 11 Restarting

    The System isnt continuously rebooting. Its done it about 8 times in 24hours. Not sure if that makes a difference

Part and Inventory Search

Back
Top