I would like to capture the source IP of anyone logging into one of our Meridian 1 or CS1K systems via rlogin. I thought this might be an SNMP trap, and it certainly may be, but when I configure an open alarm in 117, I get a message that someone connected and logged in, but I can't see the...
I'm trying to set the data VLAN ID via a system.prv file or via Nortel-i2004-B string in my DHCP server.
The IP Deskphones Fundamentals book shows dv=60 on page 447, but I can't get that to work. PCs plugged into my 1210 set jump right onto my voice LAN and ask for an IP address. When I put...
It turned out to be the workaround as it was called in the product announcement. I had to add a , before the final ; character. The latest documentation says I would have to remove that , for it to work with the 8Q, but it works with the , with either version of firmware. Thank you for the...
I haven't setup auto provisioning before, but do have experience using full DHCP. I've read the section on auto provisioning, but it leaves a lot of questions, which is why I'm here.
I'm trying to start off simple and add configuration as things go well. I haven't gotten very far, but maybe...
T1/E1 is an option, but then I'm buying a card for both systems. For less than the cost of those two cards plus the * box I can buy an MICB.
I'll continue on the current trial and error path for a while. In the not too distant future I'll try making it work with a CPDC configured as a SIP trunk...
Perhaps someone can give me a pointer or two to move my project along. I'm trying to use an Asterisk box as an inexpensive conference bridge. I don't have any connections to the Internet, or any other publicly accessible vulnerabilities, so security is NO concern. I'm completely TDM to the...
We are currently deploying Rls. 7.5 HA systems based on two CPPM cores and four CPDC cards as described above, five CPDC cards if you add the MAS server which our implementation team has never got to work correctly - but that's not the issue here. We only have a couple of these sites installed...
The majority of the systems we deploy are stand-alone, meaning not networked to another call server/PBX. Now that 7.5 is upon us we are reviewing our options for deployment. We want High Availability/redundancy. We've been told we must deploy UCM, with its primary security server and deployment...
I've built dual-boot systems in the past using a second partition on a drive by just booting from another XP install disk, but this time I started without the intent of making my system dual-boot and have changed my mind.
I have a system running XP that is made up of three hard drives; c, d...
The system has now been in service a few days and doing OK. We've had problems with our 2000 series telephones. They just don't work on some shelves so we've had to move approximately 100 to other IPEs. Once we find a suitable home for them they seem to remain stable. The customer was concerned...
We had a similar fax issue on a CS1KE cutover three weeks ago, all MG cabinets. We had to set MPTD to make them work - super G3. We considered moving fax machines to MGs holding PRIs, but too many PRIs and fax machines to make that a viable solution.
Just curious about how many of you have upgraded/migrated an Option 61C (or other large system for that matter) to a CS1000E. We're in the middle of such an upgrade, converting eight IPEs to media gateways off a CS1000E run by six CPPMs inside three MG1010 cabinets; two cores, and four...
Hey guys,
I have setup a website in IIS and it is the only one. When I try to access it from the public side it asks for a username and password. How can I get it to not ask for it?
Thanks
I've configured the above phone (192.168.6.90) and am able to make calls to DNs on my CS1K running 5.50J. I can't call from my CS1K to the Siemens phone. I've included two wireshark traces. The first shows the successful call. The second shows a failed call. I have tweaked and tweaked but seem...
You say you put two on, which sounds to me like you're sure you've got a backup. How did you archive your database - BKO from LD 43?
How did you try to restore your database, during (at the end of) the software install or from within LD 43? If I recall correctly, the first should be done from...
You may have done this already, but I'd do a DCH trace to ensure the number is being received. Once you know it is you can begin to figure out where the breakdown is occurring.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.