Search results for query: *

Hello all DS30B (700501586) is having issues with all versions of Release 11 I have tried. I get crackly noise and random ports freezing as soon as the unit comes up. It's not hard to spot the problem, at least half of the ports will have issues and it is very obvious. By the way, it is only...

1. Customer Partner ACS system caller ID working normally (incoming call shows name/number, call log shows name/number) 2. Comcast replaces existing modem and gateway with new CBR-T all-in-one modem/telephony gateway/router/wifi. 3. Caller ID starts acting weird (incoming calls normal, call...

We are auto-recording all calls to a hunt group using VM pro, and we have set to forward the message using VM to email. We noticed that even though the message is removed from the group mailbox after forwarding, the file remains in the folder in Windows. Given the frequency and length of...

@joe2938 sadly you might be right

@amriddle01, Noted. However, I am able to get other phones to load from same ports. In this case I don't think it is down to the Combo card.

File server is set for "Memory Card" by default, and yes we did reboot the IPO. We have several systems running different releases for testing scenarios. Sometimes phones get moved from one system to another, bad practice I know.

Hello This might be a common problem but I have not found a solution. I have some 1416 and 9508 sets on my test bench, that have been restarted in the middle of loading firmware. Now they don't load firmware at all. They begin loading and then at some point halt and go back to a message...

Hello to anyone who has had this problem. I have a DS30 that worked on an IP500V2 9.1 I needed to install it on an IP400V2 R5.0 and when it did not come up, I entered the IP address of the VM Pro as the TFTP server, making sure I had 5.0.22 BINS folder in the BINS directory. Then at the...

Dear tcwinont: Call Pilots only work on MICS and CICS R4.1 and later. It will NOT work on 824DS even at the latest DR5.1. Either get a Flash R1.7 or earlier, or upgrade your KSU to MICS if you really want a Call Pilot. Call me a curmudgeon but when you finally get unified messaging working...

Hi Rainman In fact, the latest I have seen of the 2.5 (617C49) is 2.5.4, and I beleive that there is a patch available for download which can be applied through the PCMCIA slot of the voice mail, in the same way as patches for the Partner Mail VS R5.0. What I am trying to find is a similar...

Does anyone know of an upgrade available for the Merlin Messaging 1.1 (Module 617A49? What is the highest release? The highest I have seen is 1.1.6. If there is a higher one, is it available as a PCMCIA upgrade card?

Sorry It isnt a font issue. Its always folders and files that are one level below the root of that drive. It happens on a drive that is connected to my secondary master cable. I am frequently changing drives and it always comes up as drive D, although when there is no drive connected to that...

Why would you get garbage characters in folder and file names when exploring an otherwise uncorrupted FAT16 drive in Win98?

How do you read the BIOS Serial Number? I am working with a 486DX266 Motherboard with AVANCE LOGIC Bios.

I wish I knew that. Do you know of a utility that will change the VOLUME SERIAL NUMBER?

Does anyone know of a PCMCIA Reader/writer device that will support writing to 12-Volt Linear Flash cards? Thanks in advance

What is the procedure for changing Partner ACS to Hybrid Mode? Something about "LUCENT" spelled backwards??

Hi Sam certain Legend mods have TTRs built in. 012, 016, 400TTR etc. So does the Merlin Mail 007. Check documentation for how many are on each type of mod. the TTR circuits are additive and are shared throughout the system (I think).

Joe Try Norton Ghost 2002 using the -ia command line switch. You have to be careful and observe the geometries of your source and desitination drives.

On this thread .... I have found several versions of the 007MLM software from 1.0 to 1.2.2 being the latest. Does anyone know if the embedded CPM DOS has a DEFRAG program which runs either periodically or on reboot?