Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: mackk
  • Order by date
  1. mackk

    1140E I/C Line becomes "stuck" when in Hunt Group BCM400

    I has same problem, until install all patches. BCM400 4.0 SmartUpdate009+165+166+168 or SmartUpdate10
  2. mackk

    BCM50 restart service

    I install last patch BCM050.SU.System.005-200712,BCM050.SU.Desktop.002-200711,BCM050.182-CORE,BCM050.183-FEPS. It does not help... I have made Level 2 reset. Configuration\Telephony\Pools is good, until then I install patches...
  3. mackk

    BCM50 restart service

    If I press the button Configuration\Telephony\Pools , I see ERROR:Error happened .... In Alarms I see :52004 **ERROR** FUMP channel not ready;MPS service aborted; then 50000,530005,..10005. I want to go under the menu,that my steps did not cause restart services.
  4. mackk

    BCM50 restart service

    ?ave BCM50 ver.1.0 If im push Telephony\Pools in Element Manager, i m take many critical alarms (52004,53005,10007 and other) and many servise is rebooting. I install all patches, but it not fix this problem. I dont have BRI , but why im couldnt see all possible feuture. If i want only see...
  5. mackk

    BCM50-1 Analog fax on main unit

    i have keykode for internal 4 ATA. i instll all patches from nortel.com incoming fax recieved - no problem, but outgoing fax very bad. Im tried panasinic ft-78 faxmashine, and HP-multifunction. Now, i dont have external ata...
  6. mackk

    BCM50-1 Analog fax on main unit

    Hi, Im connect analog fax and analog modem to main unit BCM50(ver.1).Im use analog line. I have problem.Each from 10 attempts of 1 times it is connected correctly. Without BCM, fax and modem work propertly. Someone solved such problem?
  7. mackk

    Priv.rec/pub reciev in Target line

    I want to connect some BCM with VoiP. Read the manual and tried use "Private networking: Using destination codes". This works, but not as I want. I want use Priv.Recieved digit in Target Lines,but so does not work. Its work only if use Pub.reciev digit. Why? Prompt a correct way please...
  8. mackk

    1140E Phones not able to get 2 DID Calls (Getting Busy)

    I have similar problem.BCM400,1140 and 1120 phones, 4.0 software. I have a same problem with the Intercom button(incoming call go to hunt-group). I solve this problem thus. DeRegistration-Registration phones.But it helps not for a long time. The problem exists. I have 20 IP-phones. Periodically...
  9. mackk

    Prompt plays three times...

    If to use a AAtendant custom promt, two times. If to use Menu node promt, three times. I have checked up a situation at new BCM all have repeated. Similarly.
  10. mackk

    Prompt plays three times...

    CallPilot it is adjusted as follows: AvtoAttendant - CCR-Menu Node. If caller no dial, CCR Menu Node Primary Prompt plays three times and go to the operator . I want to listen to the promt only once, and further the operator. I have BCM50(rel.1.0)on which works as I want.Menu promt once...
  11. mackk

    Promt Repeat three times..

    ?P it is adjusted as follows: AvtoAttendant - CCR-Transfer Node. If caller no dial, CCR Menu Node Primary Prompt plays three times and go to the operator . I want to listen to the promt only once, and further the operator. Change of the menu repeat key (none, 0, 1) does not help. I have...
  12. mackk

    GATM8

    yes.DIP switch in obedience to manual. BCM work during 3 months correctly.
  13. mackk

    GATM8

    ?i, All of set ring continuously. ?ctive line and inactive line of GATM8 ?re alerting in BCM Monitor. Alarm 37: Core Telephony - Failure to download market profile/protocol data from the Persistent Data Repository. All patch is installed what are ideas?

Part and Inventory Search

Back
Top