Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. seahawk04

    One way speech after transferred calls

    Thanks I have been down that road before. I will talk to my vendor and have them look into this.
  2. seahawk04

    One way speech after transferred calls

    Wanebo Thanks for the input, we did just recently have our vendor patch both sites, but I'll have to double check the versions of each Do you happen to know which vtrk patch fixed your issue?
  3. seahawk04

    One way speech after transferred calls

    Here's the scenario Call answered by operator at Site A (AACC agent) blind transferred over VTRK to Site B. Site B answers and can hear caller, but originating caller can hot hear Site B (One-way Speech). Both sites are on 7.65 To make matters worse, the problem is intermittent. Site A...
  4. seahawk04

    e911 question

    Ok, that's what i was anticipating. Threw it out there in case anyone had a different experience. Thanks again!
  5. seahawk04

    e911 question

    We need to add PKG 336 to implement subnet lookup. Does anyone know if adding this PKG requires a SYSLOAD. I know the system will tell me when I install the Keycode (I'm waiting on it from our vendor), but I wanted to plan that system restart ahead of time if it is necessary.... TIA
  6. seahawk04

    Remote worker solution

    I am looking for a recommendation for a (relatively) inexpensive VPN router that we could deploy to our home users so that may use their 1140e sets. We have deployed Cisco ASA 5505 appliances in the past, but their were fairly expensive and are hitting the end of their life cycle. We do have...
  7. seahawk04

    Agent Observe not working

    KCFLHRC - what if I want to Observe 20 agents? How can I have them all appear on the Supervisor phone? Triton - we are using WFO for Contact Recording/Quality Monitoring
  8. seahawk04

    Agent Observe not working

    Good point Juan. I could have sworn it was acquired earlier, but that could be the problem. I will acquire it and see what happens.
  9. seahawk04

    Agent Observe not working

    Need some help...tired of banging my head against the same wall. Trying to observe a couple of agents. We are on Release 7.5/AACC 6. I have a Supervisor phone programmed with SPV in CLS and OBV on Key 5. Phone is in same ACD queue as the Agent phone (not sure that matters, but it is). I...
  10. seahawk04

    Group Hunt.... timer too short??

    Thanks Chris. I was afraid of something like that. It's actually dropping shorter than 90 seconds, but it could be the carrier has a lower threshold set. I just wanted to make sure I was missing something on my end. The next step is to convince these folks to do this another way.....
  11. seahawk04

    Group Hunt.... timer too short??

    I changed RCO to 1 (CFN1 = 2) and it rings 2 times at each phone. When I use RCO 0 (CFN0 = 4) it rings 4 times at each, but only makes it halfway through the hunt chain. It is as if there is a timer set for RNA that is dropping call after abou 30 seconds. Looking for where that timer or...
  12. seahawk04

    App Builder

    Did your vendor leave you the CallPilot disks? If so, Application builder is on 1 of those.
  13. seahawk04

    Group Hunt.... timer too short??

    Having a brain fart today. I'm putting in a Group Hunt list (GHT) of 10 members. That part I have in place. Problem is if I leave CFN1 4 it disconnects half way through the hunt goup. If I change CFN1 to 2, it makes it through all the members, but two rings is too short. How can I leave it...
  14. seahawk04

    No DTMF on 1140e phones

    From what I can discern from my onsite contact, it works with some phones, not others. The issue arises when entering the a meeting code for a conference bridge (3rd party). The enter *XXXXXX*. On the phones that are having the issue, when they press the first * they get nothing, no tone, and...
  15. seahawk04

    No DTMF on 1140e phones

    Yes they are. It's not all phones having the trouble and all are on the same firmware. I'm wondering if this is more of a PRI issue?
  16. seahawk04

    No DTMF on 1140e phones

    I have some phones in of our branch offices in Spain where we cannot connect to a third party conference bridge. We are not hearing the DTMF tones. It is not all of the phones. I had the users check the settings in Telephone options to make sure DTMF was turned on those specific phones and it...
  17. seahawk04

    Department Number - How to forward

    We have a scenario where a small group (3 phones) have a an appearance of an departmental number. Phones A, B, and C. Extension 5000 is the Departmental extension. It is MARP to Phone A. What the group wants to be able to do is forward x5000 to another phone outside of the group if A, B, and...
  18. seahawk04

    Automatic Disconnect for Analog Phones

    Thanks Rita I'll give it a shot
  19. seahawk04

    Automatic Disconnect for Analog Phones

    Customer has some elevator phones that need to disconnect as soon as far end disconnects. They are set up as Ringdown (Hotline) to an internal security phone. When you press the elevator call button, it calls the security phone. The problem is that when the security desk hangs up the elevator...
  20. seahawk04

    Distintive Ring Problem

    I have a customer that would like to have distinctive ring set up for all Inbound DID calls. I assigned Distinctive Ring (DRNG = Yes) in the RDB and just left the rest default. The end user was fine with this until they started having an issue with inbound faxes. I removed the distinctive...

Part and Inventory Search

Back
Top