Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. pndb84

    NAT not translating

    changed dup to half but speed test (of 2 diff sites) shows only 3.5 down and 5.1 up. Upload showing fine but down is still much lower than bought....
  2. pndb84

    NAT not translating

    If I change dup to Half, input errors stop increasing BUT collision and deferred counters go up....
  3. pndb84

    NAT not translating

    Yes, it increases with usage. Other side is ISP though cable modem. confirmed with ISP, they are using full dup and mtu 1500.
  4. pndb84

    NAT not translating

    I've changed port and cable but still getting input errors and slow bandwidth...speedtest shows only 1.7 mg down and 1.8 up....when connected to linksys, speedtest shows 15mb down and 5 up. Anything wrong with my config ? Router#sh run Building configuration... Current configuration : 3608...
  5. pndb84

    NAT not translating

    Now getting input errors on WAN interface....I am guessing its hardware issue...anyone with suggestion ? DUP is full though Ethernet1/1 is up, line protocol is up Hardware is AmdP2, address is 0050.7320.aa52 (bia 0050.7320.aa52) Internet address is xx.xx.xx.xx/26 MTU 1500 bytes, BW 10000...
  6. pndb84

    NTP server Cisco router

    If you would like to get away with troubleshooting, you can set up ntp peer with the router that is syncronizing with ntp server....it'll work just fine.
  7. pndb84

    NAT not translating

    Thank you guys for your responces. I'll try both settings out this weekend and will post an update. Again, Thank you for helping me out....
  8. pndb84

    NAT not translating

    Can someone please help me find the issue with following simple nat transtions. I can ping everywhere from router itself but can't get internet work from PCs. What am I missing ? Router#show run Building configuration... Current configuration : 1065 bytes ! version 12.4 service timestamps...
  9. pndb84

    need a little help. point me in the right direction please!

    buy yourself a CCNA portable command guide from amazon for 30$. They have procedures for 2600 series routers.
  10. pndb84

    SX 50

    I programmed cmd 563 to trunk group 2 but that trunk doesn't accept long distance input..like if u dial 1+area code and number it gives you busy/invalid tone but it does let u dial local calls. Is there anything i am missing ?
  11. pndb84

    SX 50

    I am trying to select certain trunk number when access code 8 is dialed but CMD 152 R1 doesn't have an option. Is there any other way we can do this ? MARRY CHRISTMAS to everyone.
  12. pndb84

    SX 20 Analog....

    Thanks, Do you know where I can get the manual at for this system ?
  13. pndb84

    SX 20 Analog....

    I know this is very old old system and many of you probably dont' even try to fix it....but is this system capable of having printer hoocked up to it ? where management knows which extention is calling where and time and everything ? Thanks
  14. pndb84

    SX 50 Line Disconnects....

    This station has same cos(1 or 121) as others. It happens when you dial out to access trunk..
  15. pndb84

    SX 50 Line Disconnects....

    One of the extention has a some kind of 3 minutes disconnect timer on it. Every 3 minutes that extention disconnets. Does anyone know how to take it off ?? CMD 304 R 16(location) Thanks in advance
  16. pndb84

    SX 50 EQP-BSY

    GREAT....EVERYTHING IS WORKING FINE NOW.... I changed bit g to 0 in r2 in command 557-564. When someone calls, it appears as TRK 57,58,59,61,63,64. So, I changed programing in those comands and working fine now. no busy tones or alarms....thanks alot pandabear. Thanks,
  17. pndb84

    SX 50 EQP-BSY

    have another trunk card
  18. pndb84

    SX 50 EQP-BSY

    under status: 00 00 00 00 00 06 total:06
  19. pndb84

    SX 50 EQP-BSY

    what does blinking green light indicate?
  20. pndb84

    SX 50 EQP-BSY

    A 12 0057 .....0061 .....0063 .....0064 .....0058 .....0059

Part and Inventory Search

Back
Top