Search results for query: *

I was able to just copy and paste the 6.3 config into 7.0 and it worked fine for the most part. The commands that are giving me error are the following (pasting output below) Is there anyway to get around it? If this can't be done, what would I miss from the old config from the users...

Minue, thanks for your help. I finally figured it out. This PIX was in standby mode. I issued the "failover" command and it changed mode. After that, i was able to assign the ip to eth1 and things worked as expected. Thanks,

okay, i did a write erase and started over. here is my output. Is it safe to assume that there is something wrong with the pix? pixfirewall# conf t pixfirewall(config)# interface Ether pixfirewall(config)# interface Ethernet 1 pixfirewall(config-if)# speed 100 pixfirewall(config-if)# duplex...

i rebooted the pix and still didn't see the IP assigned to Eth1... check the following output, I am beginning to think that it is not taking my commands, any idea what i am doing wrong? my-dmz(config)# int eth1 my-dmz(config-if)# shutdown my-dmz(config-if)# show int eth1 Interface Ethernet1...

Here is the output of show eth1 sh interface eth1 Interface Ethernet1 "inside", is up, line protocol is up Hardware is i82559, BW 100 Mbps Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps) MAC address 000d.8810.48e9, MTU 1500 IP address unassigned 9012 packets...

This is a brand new PIX 535 config. All i want to do is connect to it via PDM or ASDM. I have IP'ed the interface but can't ping anything from the firewall. Here is what i get when i ping Sending 5, 100-byte ICMP Echos to 10.10.1.116, timeout is 2 seconds: No route to host 10.100.1.116 Success...

I wanted to control my traffic on the checkpoint firewall, so I installed FloodGate1 on the firewall itself (by going to voyager and turning FloodGate1 Module on) I also turned on SmartView Monitor Module from the voyager. So, i was hoping to select the QoS in Gateway Cluster properties from...

Thanks stooo; i appreciate the help.

My checkpoint Firewall on Nokia IP330 died, so i opened the box and installed a new 10GIG IDE hard drive in it. The problem is that IP330 doesn't have a CD ROM, so i am wondering how i will load IPSO on this box. This box came preloaded with IPSO so we didn't have to worry about the OS, but now...

Thanks, It was one of the object names that was giving error about a 'remark/unusual' character ... we changed the name of that object and were able to get through without the freezes.

I have two PIX 535 set up for failover. I have about 70 rules and they all have remarks/comments. When I compile the rules in ASDM, it freezes. Any suggestions? The rules are simple, it just that when i hit apply, it gives me errors regarding the remarks and then when i save it to flash, it...

I got a PIX from work; didn't know the enable password. So i am trying password reset following the procedure in the URL below http://www.cisco.com/warp/public/110/34.shtml when the pic boots up it inclines that it has version 4.3 or earlier, so i am choosing nppix.bin file to reset the...

thanks guys

I have been noticing a lot of viewpoint installations on our PCs... I still haven't figured out how it gets in.. I want to inspect the installer's exe file... i found it in user's profile/local settings/temp folder vmgrremok.exe I would love to know how it install on xp sp2 pcs without any...

thanks ...

http://www.auditmypc.com/internal-ip.html This does not necessarily mean your firewall is malfunctioning or improperly configured. The method we used will sneak past most firewalls. Why? Because we use Java to grab the information and then pass it on to the server (Notice how everything ran...

I was auditing my firewall through some utilities and i found out that my PIX is exposing internal addresses I went to this link http://www.auditmypc.com/freescan/scanoptions.asp and got this notice Notice! Our system detects your internal IP address as 10.0.1.X and your external address...

thanks fdurham... i will fix that rite now... Update on the issue, I was told that i have to update the version to 6.3 to apply the "isakmp nat-traversal" command. Is it true?

Surf Control looks great... SmoothWall is a beauty too good discussion

The best free ones are 1. Microsoft AntiSpyware 2. Adaware SE Use HijackThis too ... and check its misc tools section as well.