Search results for query: *

Recently the E1 provider replaced the paradine modem with an audio or midian 800. This has resulted in creating entry and tagging outbound calls with the pilot number. The problem I have when from any phone when I use the external forwarding feature Example 9001800xxxxx, the forwarding is not...

Hello to all CS1000 connoisseurs, I have to replace an NT8D01BC Controller 4 Card RLSE 14 and I cannot find on the market I can only get version 13 or 10 (RLSE10 or 13). Will version 13 or 10 work for me? Or should I get the same one, there is no longer on the market or I cannot find it online...

Up dates Perform the procedure to stop the NT4N39AA card without power for two hours and did not work the CPU. I installed another NT4N39AA card that provided me the client and work the CPU. (GOOD) But I made a procedure that is not documented, as this CPU was not loaded with the right...

nt4n39AA not work, no access to information by J-25 I was performing the procedure PSN003383u wait for over an hour as indicated, cards with the problem may have to wait an hour or more before re-inserting for the card to power up correctly and start functioning again. But it did not work the...

BAKLIGHTOFF in 1408 As I can make lighting 1408 phone screen turns off after a few minutes you finish a call ?, currently turns off after two hours. Someone could find and modify this parameter in IPOv2. Attentive to your comments. Cheers

BAKLIGHTOFF in 1408 As I can make lighting 1408 phone screen turns off after a few minutes you finish a call ?, currently turns off after two hours. Someone could find and modify this parameter in IPOv2. Attentive to your comments. Cheers

120000 1020000

Greetings all, By using VPN software 96xx phones against watchguard have the following problems when I connect two or three phones at the same 96xx router ip phones lose audio, the monitor appears watchguard Error ID 203 This application in watchard only works for a device or remote site...

yes, I have enable softphone HTTP provisional √ and licenses are power user and teleworker

Greetings all, This client has an IPO version 9.0.5 to use the softphone does not work. The message we see in the figure appears. In addition to the IPO have a VMPro and One-x-Portal in versions 9.0.5 Any idea or something that has been overlooked for this version 9.0.5 The client has a Win7...

The problem I am having the T7208 and T7316E phones is that when I receive a transferred call from the reception is displayed in the Telephone "Externa(Ext201)". External appears that if only Ext201 should appear I have an IPO 9.0.4 any idea

That's right, when an incoming call has no caller ID facility goes "External" The problem is that in a transfer that appears in the phone info in number of external trunk in this case and followed the number of the extension you are transferring the call, In previous versions does not appear...

I am in IPO V500 Release 9.0.4 with 2 (700501586) Norstar digital modules. The problem I have is that when I receive a transferred call from an extension in this case the ext. 248 in screen appears "Externa(Extn248)" Because the number of the trunk and then appears the extension? Someone has...

Sets 6200 as a TSC in the LD87 and embedded in ld 86 in the DMI8844

SSU 0000 Refer to best SCL Table 01

Pri These two are in the same cabinet? If you are in the same cabinet separate them and you will not have errors slip

I am installing a CP-DC with release 7.5 SIPL the idea is to use it as a PBX CS1000M . Already SIPLN and SIPL3 phones are registered and can make calls so I could is to receive calls. The problem I see is the NEXT, the customer has the 7 digit extension number as well as their extensions are...

Let me know if I can help with questions: I am installing a SMGR and SM version 6.1 Midzide Entreprice The Primary SMGR the security system will be replacing the existing CP-PM. When I am installing the software to SMGR of CS1000 I set you image patches linux mandatory. The question is whether...

I have one PN with 3 G650, currently in the slot 01C13. I need to change this card to another position like 01C14 or another position, but not the position that we stall analog and digital cards. I certainly appreciate the clarification. Amy

Now try the settings below [spalav@cores ~]$ su Password: ******* [root@cores spalav]# [root@cores /] but that was to force me to change the root password [admin@cppm ~]$ su Password: ******* You are required to change your password immediately (password aged) Password Change Utility Please...